Fro-Daddy
Well-Known Member
Still says 1 year on their website, do you know when this change is coming in to affect?
GUTEN
- Thread starter wide eyed and legless
- Start date
Help Support Australia & New Zealand Homebrewing Forum:
goatchop41
Well-Known Member
How so? It weighs barely anything, so wouldn't it only compact the grain bed if you either physically pushed it down, or put a shiteload of water on top of it by recirculating too fast/too early? It shouldn't inherently compact it, as it doesn't weigh enough, so won't increase pressure on the bed significantly compared to having the same amount of mash water on top without the screen
Dave70
Le roi est mort..
- Joined
- 29/9/08
- Messages
- 5,599
- Reaction score
- 3,279
Do you always re circulate via the return pipe? Some brewers (as in, the YT videos I've watched) prefer to adjust the flow so it remains under the return and drains (purely) back through the bed. On the face of it at, at least to me, that would seem to be the idea. Have you tried both ways? Make any difference?
wide eyed and legless
Well-Known Member
I have tried it both ways and it made no difference, I just watch the level of the liquor and make sure it holds steady, usually about half choke. you may be not able to see it but I have some silicone tube rammed in up to the taper of the bazooka, so there is nothing going down the overflow pipe.
Have a good look at the pictures I posted, the screen would be well below where the grain is sitting and tell me, why would I need the screen, there is no way the grain can escape from the malt pipe. Let the grain drift around in suspension.
In effect right now, and also giving consideration to lifting it to 3 years dependent of how things go.
No major problems like the RB3 where many have had to replace the screen and circuit board
Last edited:
Fro-Daddy
Well-Known Member
Hopefully there is a 50L single vessel price war soon!
wide eyed and legless
Well-Known Member
Now be fair, to go head to head they have to be of similar quality.
Last brew I tried a similar thing and got 80% efficiency which is above my normal 75%. I put both pipes in and had a 5.25 grain bill then I left the top screen above the pipe connector, the grain did rise up against the screen but it was first time I have been able to use the Guten pump at full flow.
wide eyed and legless
Well-Known Member
I am a great believer in if something can be done in a simple way without losing quality, then that's the way to do it. Full volume mash, = no sparge and with a ' no chill' on top of that, quicker brew day.
Dave70
Le roi est mort..
- Joined
- 29/9/08
- Messages
- 5,599
- Reaction score
- 3,279
So do you need to allow for extra grain with your recipes with the Guten? I was doing full volume brews for months with my old set up and couldn't understand why my OG always went to shit until I happened upon this article.
https://byo.com/article/skip-the-sparge/
I don’t have a gluten but that’s a good read. I have been doing full volume and wondered why I always needed to up the grain a little to hit og. I thought I just sucked.
wide eyed and legless
Well-Known Member
You can up the grain bill, but what I do is dial in a lower efficiecy, instead of 85% dial in 70% try that and tweak from there.
wide eyed and legless
Well-Known Member
80 to 85% is not unreasonable, 90 minute mash and a 90 minute boil, if I dial 70% into a recipe which is going to be a no sparge it isn't far off the mark. The usual addition without lowering the sights to 70% would be to add 20% extra on to the grain bill but most of the supporting literature was made before recirculating SVB's were on the market. Flavour improvement, I would say the only way for myself would be to do a side by side taste test, some one like Gordon Strong may pick a difference it but I doubt if I could.
Sorry WEAL, where is the mention of 2 year warranty?
malt and barley blues
Well-Known Member
- Joined
- 3/3/12
- Messages
- 613
- Reaction score
- 237
I got mine from China I wonder if that will be covered, although the 2 years are almost up.
goatchop41
Well-Known Member
I can't imagine that the local importer/retailer would cover something that was bought from the same supplier, but not through them.
The Guten manufacturers themselves in China (if we just call them 'Guten') seemed to have decent customer service prior to KK starting to import their products
They already committed to it. So if you bought from them they have to honour it.
Think you are on your own there. Distributor will only warrant what they sold. They would be pretty stupid to do otherwise unless the manufacturer recompnesed them for it somehow. imagine if you were the distributor and people asked for help on stuff you had nothing to do with?????
wide eyed and legless
Well-Known Member
2 years is going to be easy peasy, mine is very close to 2 years, only fault was the switch, but it has had some hammer, switch bought here $7.00 I have every faith in a 2 year warranty.
