Guide To Keg Forced Carbonation.

Australia & New Zealand Homebrewing Forum

Help Support Australia & New Zealand Homebrewing Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I just did my first force carb and sample from my kegs (test run before I set the rugby team loose on them after the game on Sat). Came out quite nice with a 300KPa force, shook it down to 100KPa on the dial and left it for an hour. Not sure if this one will make it as far as Saturday now come to think of it.... :eek:
- Berwyck
 
If I made a brew, but wasn't going to tap it for a few weeks/months am i best off leaving it flat and only carbonating a few days before intend to drink it?

by the way great thread, so informative and easy to follow, thanks guys

t-bone
 
Looking at setting up my first keg system. All the info on this thread is very interesting, but.....
Back at the start of the thread it was mentioned that to balance the system is dependant on the diameter of the beer out line and length of line. What I want to do to start up is just have the tap inside the fridge on the disconect. Would this method result in loads of ice-cream or are these taps regulated?
Steve
 
My understanding is that you need to turn the pressure right down when pouring - this will flatten the beer a little after a couple of beers - but you can bump up the pressure again overnight or between pours

Cheers
 
If I made a brew, but wasn't going to tap it for a few weeks/months am i best off leaving it flat and only carbonating a few days before intend to drink it?
I'm not sure that it matters either way but the few kegs that I've carbonated and left aside for a couple of months they have always turned out real nice. Better than those that I've gotten stuck into right away.
This is why I'm trying to get ahead of myself and I've been in brew overload mode so I can store some for a while. Gotta keep stocking up on those kegs. Buy em while the prices are still decent, fill them and let them sit in the corner for a while.
 
What I want to do to start up is just have the tap inside the fridge on the disconect. Would this method result in loads of ice-cream or are these taps regulated?
Steve
Do you mean a tap that connects directly to the "out" post of the keg, like this below?
http://craftbrewer.com.au/index.php?page=s...t&Itemid=29
I've got one which use with my 9L kegs and it works nicely. You just need to drop the pouring preasure.
There are regulated taps such as the Celli, which are available at the above link, but they don't fit the adaptor :(
 
Do you mean a tap that connects directly to the "out" post of the keg, like this below?
http://craftbrewer.com.au/index.php?page=s...t&Itemid=29
I've got one which use with my 9L kegs and it works nicely. You just need to drop the pouring preasure.
There are regulated taps such as the Celli, which are available at the above link, but they don't fit the adaptor
Yes thats it. I just can't see the point in having metres of beer line going to a font or a tap that needs a hole in the fridge. Otherwise I would just get a Pluto gun but they are about $100 so I reckon those taps directly on the keg are the go. Esspecially if u only drink one or 2 beers a night. Also I like to do a lot of big beers that go well in a bottle with a bit of age on em.
I know... some smart ass will drag this post up in 1 or 2 years time when I am asking how to set up my 6 tap glycol flooded font :eek:

Steve
 
Hi All..

After reading this forum for the past month, and learning a lot in the process, I am posting for the first time.

I used to kit brew and bottle years ago, now am trying my hand at AG brewing and kegging. Here's a couple of pics of my fridge setup (BTW, thanks Ross for great service and stock - most of my gear is from Ross).

Fridge_front_01.JPG

Fridge_top_01.JPG

Last night I kegged my first brew and today I performed the "Ross Method" forced carbonation. Not sure what I've done wrong, but it's definately overcarbonated (75% head while pouring @ 1PSI and flat). I have approx 1mtr of beer line for each tap (length that came with the twin tap font) and cranked the pressure up to 45PSI and shook for 60secs.. the pressure fell down to approx 10PSI after a couple more minutes of shaking so I bumped the pressure back up to 45PSI for 10 secs, then repeated process. Pressure sat at 15PSI so I assumed this was OK. It's been a couple of hours since gassing.

Can anyone help out? The beer is a Nelson Sauvin Summer Ale... tastes good, smells good, just flat with a big fluffy head ;)

Thanks,
Dan
 
Sounds like you've over carbed a touch.

The rocking after carbing should just be for approx 20seconds before you see the neddle slow right up & that's when you should read it. If you kept rocking for 2 minutes, then it would eventually drop lower.

Unfortunately the only solution is to open up the relief valve & leave for a day or 2.
Or, if you have another spare keg, pour half into that, which will then enable you to give them a gentle shake to release the gas quicker.

cheers Ross
 
Sounds like you've over carbed a touch.


Or, if you have another spare keg, pour half into that, which will then enable you to give them a gentle shake to release the gas quicker.

cheers Ross


Ross,

Have you ever poured carbonated (let alone over-carbonated) beer from a keg?

Rockin, just release some of the gas if you can. Pouring will be a big mess. Dont do it.

cheers

Darren
 
It's been about 6 or so hours since kegging. I have released gas (through release valve) a few times since - it appears that the head has reduced about 10-15%.. beer is still flat. Have now left the release valve up and will check it in a day.

I assume a day or two of leaving release valve up will make the beer completely flat and I need to restart the gassing process again? Or will it flatten the beer to a 'drinkable' level?

I have a Porter ready for kegging and want to practise on this one first ;)

Thanks,
Dan
 
Transfering from one keg to another is easy - all you need is a hose with liquid disconnects on each side. So I'm with Ross, transfer half to another keg and gentle shake - it'll be easier than dealing with next to no headspace to release the pressure.

I've overcarbed once, and the shake and release the pressure (an hour later! believe me, don't do it just after you shake!) does work - it took me abour 4 releases though over two days! At the end it was perfect, I just gassed up to serving pressure and it was right.

M
 
I have a Porter ready for kegging and want to practise on this one first ;)

To all new keggers... STOP using this method! There are dozen of posts with exactly the same story of over carbonation.

Have some patience and carbonate by hooking up at serving pressure and leaving for a week, this will allow your beer to age,clear and carbonate correctly.

The instant carbonation method works fine but you need experience and understanding of what you are doing.
 
Few guys kegging their first beer are going to wait a week to drink it.

If you are not comfortable with rapid carbonation & you are desperate to try your first beer - Simply roll back & forth at 300kpa for 30 seconds & disconnect from the gas. Then after waiting 5/10 minutes for the head to dissipate, release the pressure & reset the gas to 70kpa & continue to shake/roll until you can't hear any more bubbles being released into solution.
This will take a little longer, but will make over carbing your 1st beer impossible.

Cheers Ross
 
If I made a brew, but wasn't going to tap it for a few weeks/months am i best off leaving it flat and only carbonating a few days before intend to drink it?

by the way great thread, so informative and easy to follow, thanks guys

t-bone

Thats my understanding, and what I've done with a Coopers PA thats been sitting in the fridge for a few weeks now. Make sure you purge the head space of the keg with CO2 though.
 
It's been about 6 or so hours since kegging. I have released gas (through release valve) a few times since - it appears that the head has reduced about 10-15%.. beer is still flat. Have now left the release valve up and will check it in a day.

I assume a day or two of leaving release valve up will make the beer completely flat and I need to restart the gassing process again? Or will it flatten the beer to a 'drinkable' level?

I have a Porter ready for kegging and want to practise on this one first ;)

Thanks,
Dan

I ended up leaving the release valve open for 24hrs. The carbonation level had almost evened out. Left at pouring pressure for a couple more days then spot on.
 
About to Keg my first brew, after doing this method and putting back at serving pressure at about 100kpi do I then just leave it at that all the time, or do I turn the gas bottle off after each session?
 
About to Keg my first brew, after doing this method and putting back at serving pressure at about 100kpi do I then just leave it at that all the time, or do I turn the gas bottle off after each session?

I leave mine at serving pressure all the time, as I pretty much drink all the time.. can't think of a nicer way to put that one.. it's not a bad idea if you're getting started into kegging, etc. (and have doubts/concerns with procedure and your system) to leave the pressure at 100kpa (for example) in the reg but turn it off at the bottle overnight or between sessions, as you put it.

A certain amount of Co2 will dissolve into the beer until saturated, even after force-carbonation so don't be immediately alarmed if you wake to find your kpa in reg has dropped from 100 to say 80 overnight *and this would be after turning off at bottle. It doesn't necessarily mean you have a leak. I find my beers balance, carbonation wise, a good 3-7 days after force-carb, but certainly drinkable day 1.

Lots and lots of variables so if in doubt, just turn it off at bottle between sessions.

reVox

edit at: *
 
I gave it a shot and under carbed it. I was a bit nervous of overcarbing so now I'll just connect it up at 100kpi and leave it for a few days.
 
Got my keg setup together last night and used this method, beer came out a touch under carbed, but i am sure i will get it perfected over time, thanks guys.
 

Latest posts

Back
Top