Matho's controller

Australia & New Zealand Homebrewing Forum

Help Support Australia & New Zealand Homebrewing Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
matho said:
To compile the code additional libraries will need to be installed, the instructions on how to install libraries are found HERE
and the libraries are the 'onewire' library found HERE and
the PIDV1 library found HERE

once they are installed you should be able to compile the code with out errors

cheers steve
 
matho said:
once they are installed you should be able to compile the code with out errors

cheers steve

Thanks Matho

Now place the test result of yesterday's PCB modified
I wanted to ask one thing has not even possible and would like to improve excellent program you have done by adding an SD card reader writer for arduino you could write a log of the temperature read and PWM sent so at the end of SD cooked put the PC and check if everything went as prescription
And if you want even load the recipe from SD I can give you a hand in the test and pcb to add the SD reader but I do not know anything in programming arduino.

In Italiano

Grazie Matho

Adesso posto il risultato della prova di ieri del PCB modificato
Volevo chiederti solo una cosa mica è possibile ed avresti voglia di migliorare ottimo programma che hai fatto aggiungendo un lettore scrittore SD per arduino potresti scrivere un Log della temperatura letta e PWM inviato cosi a fine cotta mettere SD del PC e verificare se tutto è andato come ricetta
E volendo anche caricare la ricetta da SD io posso darti una mano nella parte test e pcb per aggiungere il lettore SD ma non so niente nella programmazione arduino.

Well yesterday I had two minutes to try to affect what was on paper: D

from this

Bene ieri ho avuto due minuti per provare ad incidere quanto era su carta :D

Da questo



Now place across the stage as you can see in every test I had to do three good to have one but you will know the beginning is always so: D

Adesso posto tutta la fase come si vede in ogni test ne ho dovuto fare tre per averne uno Buono ma si sa al inizio è sempre cosi :D
















 
saviothecnic said:
Thanks Matho

Now place the test result of yesterday's PCB modified
I wanted to ask one thing has not even possible and would like to improve excellent program you have done by adding an SD card reader writer for arduino you could write a log of the temperature read and PWM sent so at the end of SD cooked put the PC and check if everything went as prescription
And if you want even load the recipe from SD I can give you a hand in the test and pcb to add the SD reader but I do not know anything in programming arduino.
Today I went forward a little more: D

Oggi sono andato un altro po avanti :D

Here I am giving divided the pcb drilled sanded and cleaned with acetone
Qui do diviso il pcb forato carteggiato e pulito con acetone




First she slips on the contrary streep line and press with a piece of wood to bring out the nails flush with the plastic in order to put an LCD that goes from the high copper

Per prima cosa si infila al contrario la streep line e si preme con un pezzo di legno per far uscire i chiodini a raso della plastica per poter mettere LCD che va dal alto rame



Then you put this time the straight line where Streep is to be fixed Arduino 2009

Poi si mettono questa volta diritte le streep line dove va fissato Arduino 2009




Then with the help of a fold components are put all other components

Poi con aiuto di una piega componenti si mettono tutti gli altri componenti




Before welding you try to dry it well in Arduino 2009 he streep line mounted

Prima di saldare si prova a Secco che Arduino 2009 entra bene nell streep line montate



The same test is done for LCD

Stessa prova la si fa per LCD




I hope to have time and all the components inside so I will update you with a video of the final result: D

Spero d'avere tempo e tutti i componenti dentro cosi vi aggiornero anche con un video finale del risultato :D
 
Well we're almost there

I am missing some component, but it seems to work
Just finished all the tests'll post some pictures in the meantime all the material




 
By filling in trying to translate in Italian I have these errors: (



Yesterday I started to make the panel I designed taking into account the pattern to make a plug for the classic electrical box 200x150

Ieri ho iniziato a fare il pannello ho disegnato lo schema tenendo conto di fare un tappo per la classica scatola elettrica 200x150



Then I gave it all to feed my homebuilt cnc obviously it: P

Poi ho dato tutto in pasto alla mia cnc ovviamente anche essa autocostruita :p





The final result should be nearly this course is pitted or pasted on a sheet with the words and graphics if someone wants to do it well Come: D

Il risultato quasi finale dovrebbe essere questo ovviamente va pittato o incollato su un foglio con le scritte e grafica se qualcuno vuole farlo ben Venga :D




Grazie
 
adryargument said:
Looks great, good to see the Braudruno going international :)
http://www.saviot.com/index.php?option=com_content&view=article&id=15:braduino-italy&catid=8&Itemid=101

It is much like getting in Italy and there was nothing like it
I hope I have helped contribute to this fabulous project
I hope you do not mind

In order not to lose track I put everything in a page on my site
when it relates to the change with single-sided PCB and Italian Menu

Matho Thanks for great program you've accomplished

I wanted to ask if you can use even bigger LCD
if I write in Italian does not enter into 16x2 LCD
and if you can add to programa support SD card reader writer
Log cooked to achieve the load and maybe recipes prepared
PC and written to the SD

Matho if you want then copy the images and files also on my website
to have a double copy if you're scared like me that sites
end host on the network can

In Italiano

Spero non dispiace

Per non perdere traccia ho messo tutto anche in una pagina sul mio sito
per quando riguarda la modifica con PCB Monofaccia e Menu Italiano

Grazie Matho per ottimo programma che hai realizzato

Volevo chiederti se è possibile usare anche LCD piu grande
se scrivo in Italiano non entra in LCD 16x2
e se puoi aggiungere al programa supporto lettore scrittore scheda SD
per realizzare Log della cotta e magari caricare ricette preparate
da PC e scritte sulla SD

Matho se vuoi poi copiare le immagini e files anche sul mio sito
per avere una doppia copia se hai paura come me che i siti
in rete possano scadere host
 
Good evening everyone, I'm the pcb designer.

A new release.
I had to remap some pins.

Two cards in one pcb Eurocard format 100x160 mm.
New LCD display 4 lines of 20 columns
Backlight on / off controlled by software
Connector for SD card on board.

6,lc.jpg
 
Danielxan said:
Good evening everyone, I'm the pcb designer.

A new release.
I had to remap some pins.

Two cards in one pcb Eurocard format 100x160 mm.
New LCD display 4 lines of 20 columns
Backlight on / off controlled by software
Connector for SD card on board.
That is really cool! Are you planning on saving settings or reading beer.xml files from the SD card or something?
 
My level of programming is quite poor.
I guess now that the hardware is defined,
with the help of a programmer be able to do what you want


In any case there are still some changes to the pcb
 
Danielxan said:
My level of programming is quite poor.
I'm glad you wrote directly to you Daniel
and I thank you publicly for the availability that we're giving: D

Unfortunately from another forum

http://www.homebrewtalk.com/f170/braumiser-my-braumeister-inspired-rig-299192/index7.html

I learn that matho have some serious family problems: (
which I hope will be resolved soon and then I do not think will give us a hand
but I hope that in this forum there are programmers Arduino
that can help us migliarare excellent job of matho did
adding support Reader Writer SD

Daniel is facnedo a great job and I'm willing to test this out
Short testero the new pcb and the new LCD 40x2 with translated menus Italian
so as to be able to publish a pcb monfocaccia easy to do at home
sorpatutto and tested: D

I hope in a few days to finish the mechanical part so as to test
all on a real batch of beer
 
Two versions of the same PCB,
One with the socket SD card and one with the connector for the external SD module.
If someone wants to test the master and I can post the list of components

6,lc.jpg


7-lc.jpg
 
That is a really cool board Daniel. I look forward to seeing what can be done in the future with this project. You guys spending the time developing this stuff and making it freely available to the community is the true spirit of open source and is admirable and very much appreciated.
 
Video Test Menu Ita

https://www.youtube.com/watch?v=aX68t0n7v4A&feature=youtube_gdata_player
 
Video Test Hardware​
http://www.youtube.com/watch?v=2l_tovlTta4&feature=youtu.be​
 
And the new latest release,

Support for new display 20x4.

Socket for SD card reader.

I2c connector for RTC and expansion.

Digital Pwm pin for heater.

After the tests will be issued the master.

10-lc.jpg
 
Hi, I´m new here, I´m from Brazil and as you guys probally know, we have lots of problems here to find good Brew Stuffs.

My question is, any one has a file with all the components that I have to buy to build here, I can also buy direclty from Jaycar or from u guys;

I need a shield and also a script that can be supported by 2 Pumps and 2 Heaters.... Is it possible?

PLEASE I NEED HELP!! :(
 
This is the last variation, not yet tested.
The software is being developed, tested appeda all, will be issued.
For the two pumps and two heaters, as you can see at the moment we have exhausted the pins dell'arduino.

11-lc.jpg
 
Back
Top