Matho's controller

[MaxN68]

The Pump Cycle is from 5 to 15 minutes, the Pump Rest is from 0 to 5 minutes.
I just uploaded the same version and the setting is operating normally.

 

[stevemc32]

Gave it another go. Thought it might have been an eeprom error in the settings so I ran the eeprom clear sketch before re-uploading 2.6.63b6 and got the same result.



TimePumpRest can only be set between 10 and 15 minutes.

 

[neo__04]

just doing my controller build and run it for the first time with the buttons, leds, buzzer etc, plugged in.

A couple of things, in the setup menu, the first option is "P.I.D. Parameters" when i hit down it leaves some characters on the line... eg. "PUnit Parameterss", "P Manage Recipies s" Any idea what its doing that for? Using a 20x4 lcd.

Also the buzzer is constantly running as soon as the arduino starts.

Using the latest B6 revision.

Edit: Pump rest on latest revision with a 20x4 lcd can be set between 0-5

Any thoughts?

 

[MaxN68]

I double checked again by loading the specific version you're using (16x2 ENG) thinking about a display problem.

On my system works properly from 0 to 5.

I try to reload the file.

For the next time please tell me when you report a bug version of the language, we now have 7 languages ​​and it is impossible to debug checking everything: D

 

[MaxN68]

just doing my controller build and run it for the first time with the buttons, leds, buzzer etc, plugged in.

A couple of things, in the setup menu, the first option is "P.I.D. Parameters" when i hit down it leaves some characters on the line... eg. "PUnit Parameterss", "P Manage Recipies s" Any idea what its doing that for? Using a 20x4 lcd.

Also the buzzer is constantly running as soon as the arduino starts.

Using the latest B6 revision.

Also can confirm the above about the timepumprest 10-15 min issue

Any thoughts?

Have you select the correct PCB in sketch before load the firmware in the Arduino?

To display errors check later.

I confirm that instead of setting the pause pump works

 

[neo__04]

yes the display seems fine except for that issue in the setup menu

 

[MaxN68]

I have corrected the error display.
Firmware Revision updated (2.6.63b7)

 

[MaxN68]

Time Pump Rest Setting

 

[stevemc32]

I'm using the 16,2 ENG display, just loaded 2.6.63b7 and still see the pump rest setting display error, ie setting time available is 10 minutes to 15 minutes.

 

[MaxN68]

In the video I use the version 2.6.63b7 and I don't have errors

 

[neo__04]

Just loaded B7, running a 20x4 lcd. Selected the correct board and correct lcd and it displays like a 16x2..

Tried to flash the Italian 20x4.

I get the same result, looks like end 16x2 and rolling text for the menu options

 

[MaxN68]

From page 1 of manual



From a HW perspective the code should be adapted in order to support the correct LCD display 16x2 or 20x4. This option is configurable inside the sketch. In order to enable one or the other display the user should modify the sketch through the Arduino IDE searching for (Ctrl+f) LCD* as the search string and then apply the modifications below in both sections:
// SETTING LCD*****
// Select your LCD
// LANGUAGE ITA
#include "LCD16x2_ITA.h"
//#include "LCD20x4_ITA.h"
// LANGUAGE ENG
//#include "LCD16x2_ENG.h"
//#include "LCD20x4_ENG.h"
…...
// SETTING LCD*****
lcd.begin(16,2);
// lcd.begin(20,4);

User should remove // before the #include and lcd.begin statement for the correct size LCD and add // before the incorrect size LCD.
Moreover it’s possible to select Italian or English language in the same way modifying the first LCD section

...

 

[neo__04]

My apologies. Thanks very much.

The speed at which you keep on top of the code is amazing.

 

[claudiobr74]

Did you change this line?

 

[MaxN68]

In a few days I will start to be increasingly absent because of my job.
In a month I'll be a ghost.
Then come back in September.
We try to make everything work for good in the short time in which I can still dedicate myself to the code

 

[MaxN68]

How many people do not work the setting of the pump rest?

 

[beel]

Hi,

I'm running 2_6_63b6 and can reproduce the pump rest glitch/error, it seems like it has to do with a pumpe cylce beeing longer than 10 min.

Example: if I set pumpe cycle to 12 min, I can't set pump rest to less than 10 min. If I set pump cycle to 9 min, pump rest can be set from 1 - 5 min.

I havn't tried 2_6_63b7 yet, so I can't test it there.


Thanks for your work on developing ArdBir!

 

[MaxN68]

OK!!!
It's only a display error

 

[MaxN68]

Version 2.6.63b8 updated

 

[beel]

That's fast, I'll have a look at it tomrrow.

 

[stevemc32]

Thanks Max, pump rest time is now showing correct 0 to 5 minute scale. Cheers.

 

[Cavemanbrew]

Is there some one willing to load the new codes to my two Arduino's?

I will send with pre paid post pack to return.

I have come to the end of trying to get the circuit to connect to my bloody laptop. (Dell)

I plugged it into the computer and the green light lights up and a yellow light flashes randomly.

The part about the ports will read Arduino file thing is a no go.

I DO NOT KNOW

 

[mxd]

got mine today now need try someone to solder it up for me, my last attempt at soldering was a little atrocious

 

[lael]

Is there some one willing to load the new codes to my two Arduino's?

I will send with pre paid post pack to return.

I have come to the end of trying to get the circuit to connect to my bloody laptop. (Dell)

I plugged it into the computer and the green light lights up and a yellow light flashes randomly.

The part about the ports will read Arduino file thing is a no go.

I DO NOT KNOW

What OS are you using? Pretty easy to load. (Not helpful I know, but true) plug in USB, open up arduino and then select port, might need to select the arduino veraion you need as well. hit upload.

 

[Cavemanbrew]

Windows 7, (work laptop)
The Arduino sight, program
Plugged in the new Arduino this avo waited and waited ....................

Nothing, checked the port and ?

 

[djar007]

i can swap you a made tested and working one for your kit mxd.But I swapped the screen out for the 20x4. Teaching my daughter to solder. She is awesome at it btw. Got the knack for it. Also caveman if you are really stuck you are welcome to send it my way and I will load it for you. I know what is like when you get to a point and just want it to be done. Regards dave.

 

[MastersBrewery]

Cavemanbrew, djar007 may also be able to sort the screen scramble you were having, he has done a few now, and may be able to pick out the fault.

djar007, sorry to throw more work your way just thought if he's sending one thing to be fixed he may as well get it all done and dusted. I'm still to run mine under load so as yet to be tested so to say.

MB

 

[Cavemanbrew]

Will do,

I looked like the mad scientist off honey I shrunk the kids on the weekend trying to find the issue.

 

[MaxN68]

Someone has got to try the 2.6.65a1?

 

[claudiobr74]

Hi Max, not yet. What did you change?