Australia & New Zealand Homebrewing Forum

Help Support Australia & New Zealand Homebrewing Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
How often should I calibrate the pill? I've done a bunch of medium gravity beers and it was pretty accurate up until now. However, I just brewed a 1.080 OG, but the pill only read 1.060 when I dropped it into the fermenter.

If you use wireless charging then you pretty much will never have to calibrate again. If however you are often opening and closing the casing to charge the battery then I would calibrate every use.

When you did the initial calibration did you calibrate at 1.080? It's always best to calibrate at water being point 1 and then use the highest gravity you are likely to use being point 2.
 
Afternoon.

I'm trying to register my RAPT Pill with my network, but i've not been able to get it to take me to the 'captive portal'. I've tried on by phone (android) and my windows based laptop. Neither open up the 'captive portal', and as i can't get it to the wifi network to open the 'captive portal', i can't enter via the Pills IP address.

Am i missing something? Perhaps this has been answered before, but i couldn't find anything.

Hawk
 
Afternoon.

I'm trying to register my RAPT Pill with my network, but i've not been able to get it to take me to the 'captive portal'. I've tried on by phone (android) and my windows based laptop. Neither open up the 'captive portal', and as i can't get it to the wifi network to open the 'captive portal', i can't enter via the Pills IP address.

Am i missing something? Perhaps this has been answered before, but i couldn't find anything.

Hawk
Got it to work. Issue was my phone antenna continually switched back to my home wifi as it couldn't find a wifi connection via the RAPT Pill connection.
 
Does a new Digiboil need to be passivated or just cleaned with PBW and rinsed?
 
Wash it twice and dry . Passivated.
Ok, so just Stellarclean (PBW) wash it twice, with no phosphoric acid soak. The instruction sheet is vague but it does just say that they (Kegland) recommend washing with PBW before first use. No concentration is recommended so just used 1 g per litre.

I started with 65 grams dissolved in 45 litres, which I then brought up to 50'c. I used a microfibre cloth to wash the upper wall and then filled it to 65 litres, raised to 60'c and held for 30 minutes. Power off and drained the hot cleaner into kegs. Spray rinsed with fresh water and emptied to dry.

You reckon I should repeat?
 
You just want to remove all oils and contaminants. Washing and rinsing and washing again just ensures that you got it all.
When stainless steel air dry's it self passivates.
 
@KegLand-com-au do you guys recommend thread tape when using your MFL to Barb adaptors on one of your gas line manifolds?
I've just had 3 MFL to Duotight adaptors start leaking (through their body cracking) over about a month and lost a 6kg & 2.6kg bottle of CO2, I didn't notice more had cracked until after I'd replaced the first leaking one 😓
 
@KegLand-com-au do you guys recommend thread tape when using your MFL to Barb adaptors on one of your gas line manifolds?
I've just had 3 MFL to Duotight adaptors start leaking (through their body cracking) over about a month and lost a 6kg & 2.6kg bottle of CO2, I didn't notice more had cracked until after I'd replaced the first leaking one 😓

Thread tape is not required on these fittings. If you use the fittings and tighten to the correct torque you will not get leaks and cracking.

My advice would be to do up the fittings as tight as you can by hand and then tighten by an additional 180 degree using a spanner. This will give you ample compression without cracking.

The only other reason for cracking that I am aware of is that some customers would repeatedly spray the outside of the fitting with sanitiser and then air dry. When the sanitiser dries the concentrations of the acid would get close to 100% as the water evaporates and this would damage the acetal plastic. With that said the new MFl Fittings here are made with POK:
https://kegland.com.au/products/duotight-8mm-5-16-female-x-ffl-female-thread-to-fit-mfl-disconnects
The new POK plastic can handle pure phosphoric fine so even this unlikely failure mode has been solved and it's one of the advantages over the John Guest brand that is still using acetal.
 
Hi @KegLand-com-au

Will you please consider making these baskets? but taller to maximise grain bill payload, and much cheaper, of course 😉

https://www.ebay.com.au/itm/1656958...Vz5zDpWSJ6&var=&widget_ver=artemis&media=COPY

These are really easy to manufacture and we have looked at this previously. The only issue is they are quite inefficient and you will fine a signficant loss in efficiency especially if you are fly sparging.

I will bring this up with the other product development team and we will raise this again as it's been spoken about a few times in the past.
 
HI @KegLand-com-au any info on when the polyphoenix still kit will be back in stock?
Cheers.

The PolyPhoenix products have been quite quite difficult to keep in stock as they have been selling quite well but also there are a lot of small components and when one common component sells out of stock it removes all the derivative components out of stock. We have a container arriving on 23st March and then another container arriving about 10th April. If you check the website close to these dates the products will be back in stock but I assume once the container lands they will sell out again quite fast so you probably want to purchase within a few days of the container landing.
 
Got it to work. Issue was my phone antenna continually switched back to my home wifi as it couldn't find a wifi connection via the RAPT Pill connection.

It's probably best for you to email us a video of the process that you are trying. We have found this to be most useful and it generally speeds up the troubleshooting a lot if we can get a video from you.
 

Latest posts

Back
Top