Mantis
Official keg inhaler
- Joined
- 4/3/08
- Messages
- 1,328
- Reaction score
- 3
Mill positioned on base
Attatched and tightned up to see if roller spin freely, and they did
![002.JPG 002.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26641-7d7b90c3e109cbd6a15abda79fe2f218.jpg)
Hole cut in bottom
![003.JPG 003.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26642-3b84f9e58263ee1b31a9e260a4c031ce.jpg)
Top plate for hopper attatched and tightned and rollers still spin freely, so all good so far
![004.JPG 004.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26643-0c34b79d41f0237f8724378e06e903e1.jpg)
Bits for hopper cut out
Supports attatched to sides
![008.JPG 008.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26645-ceb51be968c0e8bfe155fe91e5acb99f.jpg)
Hopper put together and top plate and mill attatched
Base attatched
![010.JPG 010.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26647-d6ca5c45ad49c6abeca2355cfb269a53.jpg)
Done
![015.JPG 015.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26648-62f4ecd292ecea2041e535859ebfdd02.jpg)
I also added a slide shutoff and the bottom of the hopper so I can fill the hopper, get the mill going then open the slide. Hopefully this will make the job easier and get the free spinning roller going
![012.JPG 012.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26649-d47765664c7982332b9ffa7ce615c516.jpg)
Slide open
![013.JPG 013.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26650-ef49bb450f4ff64609474b7a128016aa.jpg)
And closed
![014.JPG 014.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26651-e8c45bacd71d9332a020d70c21df4c85.jpg)
![001.JPG 001.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26640-19cec8a250a28b151117d36bb50a9a31.jpg)
Attatched and tightned up to see if roller spin freely, and they did
![002.JPG 002.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26641-7d7b90c3e109cbd6a15abda79fe2f218.jpg)
Hole cut in bottom
![003.JPG 003.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26642-3b84f9e58263ee1b31a9e260a4c031ce.jpg)
Top plate for hopper attatched and tightned and rollers still spin freely, so all good so far
![004.JPG 004.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26643-0c34b79d41f0237f8724378e06e903e1.jpg)
Bits for hopper cut out
![007.JPG 007.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26644-2b4002214acf74fe9a2a3be2782c19cb.jpg)
Supports attatched to sides
![008.JPG 008.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26645-ceb51be968c0e8bfe155fe91e5acb99f.jpg)
Hopper put together and top plate and mill attatched
![009.JPG 009.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26646-57f5bf66e267ecd15adfe33601a57f7b.jpg)
Base attatched
![010.JPG 010.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26647-d6ca5c45ad49c6abeca2355cfb269a53.jpg)
Done
![015.JPG 015.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26648-62f4ecd292ecea2041e535859ebfdd02.jpg)
I also added a slide shutoff and the bottom of the hopper so I can fill the hopper, get the mill going then open the slide. Hopefully this will make the job easier and get the free spinning roller going
![012.JPG 012.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26649-d47765664c7982332b9ffa7ce615c516.jpg)
Slide open
![013.JPG 013.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26650-ef49bb450f4ff64609474b7a128016aa.jpg)
And closed
![014.JPG 014.JPG](https://cdn.imagearchive.com/aussiehomebrewer/data/attachments/26/26651-e8c45bacd71d9332a020d70c21df4c85.jpg)