• If you have bought, sold or gained information from our Classifieds, please donate to Aussie Home Brewer and give back.

    You can become a Supporting Member or click here to donate.

Herms For Sale / Brisbane / $1000.00

Australia & New Zealand Homebrewing Forum

Help Support Australia & New Zealand Homebrewing Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

camelbak28

Member
Joined
3/10/11
Messages
21
Reaction score
9
Herms For Sale.
$1000.00
Location- Ashgrove, BRISBANE

For sale is my Herms build. I built a Brau Clone when I made this as well and two small rug rats and a third on the way isnt allowing the time of old to tinker, so I’m scaling back to just brewing on the Brau.

I’m looking to sell everything as one lot, but will look at splitting if it doesn’t move. I think $1000 is fair for the gear here, but haven’t been looking at brew gear for a while, so I might be a bit off, apologies if so.

Long story short l built the Herms as per the completed pic with 2 electric elements and a gas boiler and made several brews on the system until I got bit by the brew bug bad and decided to go fully electric as per - http://www.theelectricbrewery.com/

To this end I partially disassembled the herms a couple years ago as per the remaining pics with the intent of converting to fully electric and replacing all brass, however now I have a greater hobby of my children so don’t have the time to tinker and complete the conversion. All gear has been boxed and covered.

This Herms would suit someone who wants a near complete system that could be returned to its original state with a few hours work and plumbers tape or someone looking for more of a challenge who doesn’t want to spend days chasing parts etc to convert it to fully electric, most of the major parts are there and good to go, more the wiring up side that needs completing.

The frame is custom made and mounted on heavy duty castors for ease of movement and is 145cm long and 65cm high.

All kegs are fitted with Mash Master temp gauges to aid in accurate temp control, along side the PID electronic temp sensors and have glass lids.

All Keg fittings are welded.

The Water and mash tun are heavily insulated and the boiler polished.
The mash tun has a stainless false bottom and new unused Blichmann sparge arm.

There is a new stainless Herms Heat exchanger / element for the heart of the system to replace the drum and stick heater of my first version.

In my planned refurbishment I decided to start over and replace all brass parts and connectors with stainless fittings / pipe and cam locks. As per the pics below there are new stainless fittings / taps and cam locks to replace all brass on the system.(Cam Locks, new from cheeky peek)

I purchased a large amount of electrical gear, (Auberins ((Ramp / Soak controller for the Heat Exchanger) and Sestos PIDS for the water heater and Boiler)temp sensors, SSR and heat sinks.
There is a huge quality Forte Electrical Box (50cm x 50cm x 30cm), to fit all the PIDS, switches, lights and alarms into, you won’t be trying to squeeze gear in there.

There are (2)wired March pumps to drive the system and metres of heavy duty silicon tubing (4mm thick walls), not the cheap thin stuff.

Included is the Rambo burner (with new regulator) and aluminium mounting plate from under the original boiler.

Please PM with any questions.

Cheers

Mick



View attachment 111334View attachment 111335View attachment 111336View attachment 111337View attachment 111338 View attachment 111342View attachment 111343View attachment 111344View attachment 111345View attachment 111346View attachment 111347View attachment 111348View attachment 111349View attachment 111350View attachment 111351View attachment 111352 View attachment 111339View attachment 111340View attachment 111341View attachment 111353View attachment 111354View attachment 111355View attachment 111356View attachment 111357View attachment 111358View attachment 111359View attachment 111360View attachment 111361View attachment 111362View attachment 111363View attachment 111364View attachment 111365View attachment 111366View attachment 111367View attachment 111368View attachment 111369View attachment 111370View attachment 111371View attachment 111372View attachment 111373View attachment 111374View attachment 111375View attachment 111376View attachment 111377View attachment 111378View attachment 111379View attachment 111380View attachment 111381View attachment 111382
 

Attachments

  • IMG_0419.jpg
    IMG_0419.jpg
    68.3 KB
  • IMG_0421.jpg
    IMG_0421.jpg
    97.8 KB
  • IMG_0425.jpg
    IMG_0425.jpg
    93.2 KB
  • IMG_0434.jpg
    IMG_0434.jpg
    105.6 KB
  • IMG_0436.jpg
    IMG_0436.jpg
    85.7 KB
  • IMG_0441.jpg
    IMG_0441.jpg
    98.8 KB
  • IMG_0443.jpg
    IMG_0443.jpg
    71.8 KB
  • IMG_0474.JPG
    IMG_0474.JPG
    242.3 KB
  • IMG_0475.JPG
    IMG_0475.JPG
    100.1 KB
  • IMG_0479.jpg
    IMG_0479.jpg
    91.9 KB
Last edited:
Hey Mick, the pics don't seem to work...

I get this error message.

"Aussie Home Brewer - Error
You do not have permission to view this page or perform this action."
 
Thanks for that, I’ll try and reload them
 

Attachments

  • IMG_0413.jpg
    IMG_0413.jpg
    95.2 KB
  • IMG_0417.jpg
    IMG_0417.jpg
    109.8 KB
  • IMG_0420.jpg
    IMG_0420.jpg
    70.9 KB
  • IMG_0422.jpg
    IMG_0422.jpg
    104.1 KB
  • IMG_0428.jpg
    IMG_0428.jpg
    62.4 KB
  • IMG_0431.jpg
    IMG_0431.jpg
    68.7 KB
  • IMG_0445.jpg
    IMG_0445.jpg
    78.8 KB
  • IMG_0476.JPG
    IMG_0476.JPG
    86.7 KB
  • IMG_0477.JPG
    IMG_0477.JPG
    103.8 KB
  • IMG_0478.JPG
    IMG_0478.JPG
    105.4 KB
[emoji23] Tks, Nothing is easy, I’ll try uploading pics from my lap top
 
Herms For Sale.
$1000.00
Location- Ashgrove, BRISBANE

For sale is my Herms build. I built a Brau Clone when I made this as well and two small rug rats and a third on the way isnt allowing the time of old to tinker, so I’m scaling back to just brewing on the Brau.

I’m looking to sell everything as one lot, but will look at splitting if it doesn’t move. I think $1000 is fair for the gear here, but haven’t been looking at brew gear for a while, so I might be a bit off, apologies if so.

Long story short l built the Herms as per the completed pic with 2 electric elements and a gas boiler and made several brews on the system until I got bit by the brew bug bad and decided to go fully electric as per - http://www.theelectricbrewery.com/

To this end I partially disassembled the herms a couple years ago as per the remaining pics with the intent of converting to fully electric and replacing all brass, however now I have a greater hobby of my children so don’t have the time to tinker and complete the conversion. All gear has been boxed and covered.

This Herms would suit someone who wants a near complete system that could be returned to its original state with a few hours work and plumbers tape or someone looking for more of a challenge who doesn’t want to spend days chasing parts etc to convert it to fully electric, most of the major parts are there and good to go, more the wiring up side that needs completing.

The frame is custom made and mounted on heavy duty castors for ease of movement and is 145cm long and 65cm high.

All kegs are fitted with Mash Master temp gauges to aid in accurate temp control, along side the PID electronic temp sensors and have glass lids.

All Keg fittings are welded.

The Water and mash tun are heavily insulated and the boiler polished.
The mash tun has a stainless false bottom and new unused Blichmann sparge arm.

There is a new stainless Herms Heat exchanger / element for the heart of the system to replace the drum and stick heater of my first version.

In my planned refurbishment I decided to start over and replace all brass parts and connectors with stainless fittings / pipe and cam locks. As per the pics below there are new stainless fittings / taps and cam locks to replace all brass on the system.(Cam Locks, new from cheeky peek)

I purchased a large amount of electrical gear, (Auberins ((Ramp / Soak controller for the Heat Exchanger) and Sestos PIDS for the water heater and Boiler)temp sensors, SSR and heat sinks.
There is a huge quality Forte Electrical Box (50cm x 50cm x 30cm), to fit all the PIDS, switches, lights and alarms into, you won’t be trying to squeeze gear in there.

There are (2)wired March pumps to drive the system and metres of heavy duty silicon tubing (4mm thick walls), not the cheap thin stuff.

Included is the Rambo burner (with new regulator) and aluminium mounting plate from under the original boiler.

Please PM with any questions.

Cheers

Mick



View attachment 111334View attachment 111335View attachment 111336View attachment 111337View attachment 111338 View attachment 111342View attachment 111343View attachment 111344View attachment 111345View attachment 111346View attachment 111347View attachment 111348View attachment 111349View attachment 111350View attachment 111351View attachment 111352 View attachment 111339View attachment 111340View attachment 111341View attachment 111353View attachment 111354View attachment 111355View attachment 111356View attachment 111357View attachment 111358View attachment 111359View attachment 111360View attachment 111361View attachment 111362View attachment 111363View attachment 111364View attachment 111365View attachment 111366View attachment 111367View attachment 111368View attachment 111369View attachment 111370View attachment 111371View attachment 111372View attachment 111373View attachment 111374View attachment 111375View attachment 111376View attachment 111377View attachment 111378View attachment 111379View attachment 111380View attachment 111381View attachment 111382
Did you end up getting cash for herms
 
Back
Top