Improving Effiency

Australia & New Zealand Homebrewing Forum

Help Support Australia & New Zealand Homebrewing Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

KHB

All Grain All The Time
Joined
23/5/07
Messages
1,138
Reaction score
1
I have always got 67-68% effiency. I batch sparge at 75 degrees and try to keep it slow. I use a braided stainless steel line for my mash tun.


How do you improve your effiency??
 
Latest issue of BYO mag has a good article on it

The conclusion was that the crush plays the biggest role on the homebrewing scale.

IIRC you crush as fine as possible to still allow a decent runoff rate.
 
A recirculating system (RIMS or HERMS) also yields high efficiencies. I got 70% before the HERMS, 85% after.
 
Agree with Dr S, that's why I am getting a Monster Mill and retiring the PhilMill :D

C&B
TDA
 
I am using a barley crusher and have it on the original settings which seems a pretty fine crush
 
When batch sparging it is important to give the mash a good stir and a 10 min rest after adding the sparge water. That way you rinse the grain better and get most of the sugars out.

I rushed this one day and gave it a quick stir and then ran off and my efficiency dropped by about 10%

Kabooby :)
 
i stir it and recurculate it back onto itself for 2 mins before sparging
 
I am using a barley crusher and have it on the original settings which seems a pretty fine crush
I too use a barley crusher, but got a 10% increase when I closed the gap from the factory setting. From memory I use about 0.7mm now.
 
Yup, the BYO article did suggest 0.7mm was the optimum gap. I should get myself a set of feeler gauges to check mine.

I get a constant 70% so am happy with that at the moment, I'm trying to focus on improving my beers rather than save a few $ on grain.
 
I get 80-85% with batch sparging on most brews.

Previously it was 75-80% (still not bad).

My efficiency improved with finer crush (a few handfuls rice hulls in the mash to keep it flowin').

Also, adding gypsum and a little citric acid to lower PH. Not much, as my water is very soft anyway, but I was told that helps with extraction.

Anyway, it works well for me.
 
I used to consistently get about 65% using grain crushed at the HBS and batch sparging.
First crush with the new Monster mill improved that to 82%.
 
I used to consistently get about 65% using grain crushed at the HBS and batch sparging.
First crush with the new Monster mill improved that to 82%.

+1 :D

I'm getting similar figures to Rob.

FWIW My MM2 is gapped to 1.1mm... You 0.7 & 0.8mm guys are scarin' me. :eek:

Warren -
 
I too use a barley crusher, but got a 10% increase when I closed the gap from the factory setting. From memory I use about 0.7mm now.


I will borrow some feeler gauges and test this out!
 
Efficiency will be effected by your equipment, your crush, your technique and even the maths you use to calculate it. I used to batch sparge and with my system this was inefficient. I use SS braid - I had a small length of it in the mash tun and then upgraded to 1.5 metres looped. This upped my efficiency. Also I worked out how to put the numbers into promash properly and this upped my effiency. My crush is pretty good as I have a barley crusher but I found you can crush much finer with better lautering and mashing equipment - now I can crush finer without getting a stuck sparge. My efficiency is now around 85%+ but I have switched to flood and on the fly sparging. Is it all worth it? Money wise and time wise probably not but I understand what is happening in my mash tun now and how to adjust things

lou
 
+1 :D

I'm getting similar figures to Rob.

FWIW My MM2 is gapped to 1.1mm... You 0.7 & 0.8mm guys are scarin' me. :eek:

Warren -

I'm with Warren on this, although I'm not as big a sook as he is :p , mines gapped to 1.0mm, my efficiency is 82%.
I've found with the HERMS continuously recirculating the wort the crush doesn't need to be so fine, I get very little flour in my crush either.

Andrew
 
I also feel when i upgrade to my SS mash tun with a SS false bottom and bottom drainage that my efficiency will improve as i didnt do the best job drilling the hole in my esky



I also find i get a decent amount of flour in my crush
 
With my Crankandstein (much like a MonsterMill) I was noticing that while all grains were getting cracked, a lot of them stayed whole. So last brew I ran the whole grist through twice (hand cranked I might add!). The quality of the crush was visibly much better after the second pass and the efficiency picked up from 70% to 77-78%. My batch sparge technique may have been better as well, but I think the crush was the main contributior to the better yield. A pump sure would be nice ...
 
can someone remind me of the basic equation for working out efficiency again?
 
Back
Top