Amount Of Bulk Priming Sugar For A Regular 23l Run

Australia & New Zealand Homebrewing Forum

Help Support Australia & New Zealand Homebrewing Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Well I have finsihed bottling 3 runs.
I used a round 200 gm in the end (ok, probably 210 gm).
Most were into PET bottles, so I'm not really concerned about bottle bombs.
And I love head.
I would far prefer too much head than not enough.
.
What I find slightly strange about all of this is, when I have put sugar in the bottles (I have been using 2 teaspoons per litre) the alternative was the Coopers drops. 1 per 375ml, 2 per 750ml. Obviously there is no scope for +/- adjustments with the drops.
What does a Coopers drop per stubbie work out as?
 
FWIW, I just primed 19L of RIS with just 66g of sugar for 1.8 volumes. Style is the real key IMO, so I pay more attention to the carbonation volumes for the particular style being bottled, while temperature is usually only a minor component.

If you play around with the temps, from one end of a realistic scale to the other (say an ale, so 15C to 22C), you'll see it makes SFA difference in the end. Eg. my RIS wanted 68g at 22C and 55g at 15C, so 13g difference, a maximum of 25% from ideal. Hardly worth losing sleep over, I'd say most drinkers wouldn't even notice a difference of that order...
 
3 volumes of CO2 is very high for my liking, and is right up there at the level for Hefeweizens.
You'd better be darn sure our brews are fully fermented out, as you'll get lots of bubbles at that level.

For a 23 litre batch of Mild, I've primed with as little as 80 gr of caster sugar, and they've been adequately carbonated.
 
3 volumes of CO2 is very high for my liking, and is right up there at the level for Hefeweizens.

A few have said that 3 is very high.
I had no idea what to use, and only used 3 because the "tool" recommended 2.9-3.1 for
homebrew general, which just about sums me up!

ScreenHunter_02_May._23_23.04.jpg
 
A few have said that 3 is very high.
I had no idea what to use, and only used 3 because the "tool" recommended 2.9-3.1 for
homebrew general, which just about sums me up!

Mike,
dont stress.....it will be sweet. I love a reasonably well carbed beer, 200gm will rock it. I usually go between 180 - 220. Just be sure (as others have said) that fermentation has finished, otherwise there will be extra sugars, meaning extra CO2, meaning extra pressure, meaning possible kaboom-ies, but PET kaboomies are better than glass kaboom-ies. I always leave the beer in the ferm for at least a week after it has fermented, for a variety of reasons. Good practice generally ...(always exceptions)....

rendo
 
what style beer are you brewing?? As I say try work it out to actual volume not what volume is in the fermenter as you have 23lts but 2lts maybe trub. Why I brew 25lts I found I get the 30 bottles or 23lts out of that. so if you brewed 23lts you might only bottle 21lts.
 
Mike,
dont stress.....it will be sweet. I love a reasonably well carbed beer, 200gm will rock it. I usually go between 180 - 220. Just be sure (as others have said) that fermentation has finished, otherwise there will be extra sugars, meaning extra CO2, meaning extra pressure, meaning possible kaboom-ies, but PET kaboomies are better than glass kaboom-ies. I always leave the beer in the ferm for at least a week after it has fermented, for a variety of reasons. Good practice generally ...(always exceptions)....

rendo

ty rendo, that is reassuring.

kelbygreen,
I have 3 kits that I bottled. They were all 21 days in the drum, and had final SGs of 1010 to 1012.
#13 B1 Coopers Dark Ale + Tooheys Liquid Brewing Sugar P2/5/2010 S23/5/10
#14 B2 Coopers Dark Ale + Tooheys Liquid Brewing Sugar P2/5/2010 S23/5/10
#15 B3 Brigalow Larger + 150gm Coopers Brewing Sugar P2/5/2010 S23/5/10



I found this link:
http://www.aussiehomebrewer.com/forum/inde...;showarticle=79

This gives a further explaination of the variables of the "tool" in particular the temperature to use.
 
Examples:

22L of beer at 15 deg 125g sugar = carbonation level of 2.5 volumes (1.01 volumes of residual Co2 in the beer)
22L of beer at 22 deg 125g of sugar = carbonation level of 2.3 (0.81 volumes of residual Co2 in the beer)

Oh FFS - Now thats well worth worrying about eh! :lol:

Screwy
 
FWIW, I just primed 19L of RIS with just 66g of sugar for 1.8 volumes. Style is the real key IMO, so I pay more attention to the carbonation volumes for the particular style being bottled, while temperature is usually only a minor component.

If you play around with the temps, from one end of a realistic scale to the other (say an ale, so 15C to 22C), you'll see it makes SFA difference in the end. Eg. my RIS wanted 68g at 22C and 55g at 15C, so 13g difference, a maximum of 25% from ideal. Hardly worth losing sleep over, I'd say most drinkers wouldn't even notice a difference of that order...


I have just fermented an 23 litres of RIS , @18C

SG 1091 FG 1028

see my thread

http://www.aussiehomebrewer.com/forum//ind...c=44615&hl=

using the calculator , for irish dry stout ( is this OK for an RIS ), it suggests 82g

I like a good head so was going to add 100g of dextrose , this would be a bit more than your addition which would be 82g for my 23 litre batch

how significant would the extra 18 g be

probably more worried about bottle bombs

is your RIS batch finished

maybe 82g is the way to go

your advise please
 
Examples:

22L of beer at 15 deg 125g sugar = carbonation level of 2.5 volumes (1.01 volumes of residual Co2 in the beer)
22L of beer at 22 deg 125g of sugar = carbonation level of 2.3 (0.81 volumes of residual Co2 in the beer)

Oh FFS - Now thats well worth worrying about eh! :lol:

Screwy


In those circumstances no it's not. But what if you cold condition or lager? Fair bit of difference between a beer at 20 degrees (around 145g for 2.5 vol in 22 litres) and a beer at 2 degrees (80g for the same vol). That is worth worrying about.

@Michael Aussie and others - don't confuse head with carbonation. Sure there's a connection but you can have fizzy beer that fails to hold a head and lightly carbonated beer that forms and holds a nice, dense creamy head. 4 vol won't necessarily give a better retained head than 1.9.
 
In those circumstances no it's not. But what if you cold condition or lager? Fair bit of difference between a beer at 20 degrees (around 145g for 2.5 vol in 22 litres) and a beer at 2 degrees (80g for the same vol). That is worth worrying about.

@Michael Aussie and others - don't confuse head with carbonation. Sure there's a connection but you can have fizzy beer that fails to hold a head and lightly carbonated beer that forms and holds a nice, dense creamy head. 4 vol won't necessarily give a better retained head than 1.9.

Manticle ,

I thought you might have answered my previous thread on priming Dan's RIS

will I be OK with 82g or should I use 100g
 
I did partially answer it - head is not directly related to volumes of C02.

I'm not an RIS expert so take what I say with a grain of salt. It's what I would do in your situation.

First of all make sure it's finished. Then you don't need to worry about bottle bombs. Take a hydrometer sample tube full and put it in a stubby (clean but sanitised is unnecessary). Seal it and shake the crap out of it. Allow it to sit indoors where the temp might hit 20-30 degrees. After a couple of days, measure the gravity, reseal, shake and leave again for a few more days and see if the gravity has dropped. Once you get stable gravity you should have an idea of expected FG. If the FG in the fermenter is close to that then prime with whatever amount you like.

Because you are ageing an RIS (presumably) you have a long time for carbonation to take place so low carb is not a bad thing (suits the style too). I think anything between 80 and 100 will be fine - if you are worried split the difference and use 90g.
 
here you go real science heres the graph
174solublegas.gif

and the web page http://www.elmhurst.edu/~chm/vchembook/174temppres.html

so going by this the lower the temp the more co2 is absorbed at a lower pressure. therefore if your cold conditioning your beer sits under a layer of co2 right. at low temps its enough for this gas to be dissolved at room pressure. hence why its more important to be the current temp of the beer not the highest temp reached as i was explaining.

With this point below you make it sound impossible to force carb a beer. Hence by lowering the temp we can negate the need for a high pressure to speed up the absorption of co2.
what im saying is true you can get around this by simply warming the beer back to room temp after cold conditioning.
any way using my brewing program i get that you wanted to add 8.6 g per L to get the desired 3 volumes at 20 degrees beer temp
while at 10 degrees it drops to 7.3 g per L and at 0 its 5.1g per L. this is taking in to account of the dissolved CO2 in the beer.
Sorry Barls, but this is not correct.
The beer does not absorb any C02 while cold conditioning (after fermentation is finished). In fact, cold conditioning does not affect your residual C02 levels at all. Only warming the beer will make it loose C02. The beer can only absorb C02 during fermentation (or through pressure of course).

Here is a passage from an AHB article about bulk priming:

So in an example of fermenting for 5 days at a constant 18C (with FG being stable for the last 48hrs), then being crash chilled;

The level of CO2 remaining at 18C is now stable, because you've given it enough time to confirm that fermentation has finished, which allows enough time to desaturate to the level it would normally be at for 18C. The chilling then does nothing in regard to the CO2. If you bottle at this point, then you would use 18C for your saturation level.

If you warm the beer before bottling.......if it is warmed to any point under 18C, then 18C is still used. If it is warmed to a temperature over 18C, then the new temperature would be used....


Hope that clears things up now. As said earlier, always use the warmest temperature the beer has ever been from a few days into fermentation til bottling. Obviously, if you expose a full fermenter to 35 degrees ambient temperature for an hour only, this will not affect the beer temperature as it needs more time to warm up completely.

Florian
 
how significant would the extra 18 g be
Most likely not very significant. Don't lose sleep over it would be my advice as it won't be a show- stopper.
probably more worried about bottle bombs
Precisely. I'm hardly a RIS specialist, so just like manticle, but I'd be sure that sucker is finished, that's why mine spent a few extra weeks at the end of the bottling queue. Sure enough, it dropped a couple of points in that time.
 
@barls:

I'm still confused. The way I interpret what you're saying is that co2 will be dissolved back into solution at cold temps. However the co2 has to come from somewhere. If you leave a beer in secondary like I do for 3-7 days after FG is reached then where does that co2 come from? When I cold condition, my beer is flat and the co2 has dissipated.

Not trying to argue with you - I have an inkling you know much more about brewing than I.
 
it can come from the layer of co2 the beer is sitting under in the fermentor especially if you are using the same fermentor. as during fermentation this layer is not completely removed only vents off the excess from the co2 production during fermentation.
this is also one of the reasons why if you use a secondary, it can have very minimal head space as compared to a primary.
yeah i do know a little bit about this as im actually trained as a hydraulics and pneumatics tech.
 
Barls, am not trying to argue either, just trying to understand it (which I thought I had). Picking up on Manticle's point, if I ferment in primary, then secondary and for traditions sake then transfer to a lagering vessel without head space, where would the C02 come from, when I do a D-Rest in secondary and then transfer warm to the lagering vessel? The way i understand it is that there then sholdn't be a C02 layer anymore, and therefore no C02 can dissolve into the beer.

This whole "which temperature to put in the priming calculator issue" used to bugger me quite a bit and I therefore searched for an answer. That's how I ended up on the AHB article which surprisingly says the exact opposite from what you say. Apart from what I quoted yesterday it also says: 5. Decrease in temperature, leading to the uptake of CO2 (This is also discarded, because as liquid cools it will reabsorb CO2, but only if there is top pressure as well as a source of CO2.

I am still not convinced, and am wondering two things:
1.If you are right, then who wrote the AHB article?
2. If you would have a half full bucket of cold water, and would pump a layer of C02 onto it (even cover the whole thing with a lid if you like), would you then get soda water (lightly carbonated only) without applying any pressure to it?

As I said, am not trying to argue and am happy to be corrected.

Florian
 
it can come from the layer of co2 the beer is sitting under in the fermentor especially if you are using the same fermentor. as during fermentation this layer is not completely removed only vents off the excess from the co2 production during fermentation.
this is also one of the reasons why if you use a secondary, it can have very minimal head space as compared to a primary.
yeah i do know a little bit about this as im actually trained as a hydraulics and pneumatics tech.


My impression is that the co2 blanket has a finite life. How long does it last?

The reason I'm asking is because I cc all my beers and up until recently this question confused the hell out of me. Therefore I used to let everything warm to ambient before bottling so I didn't have to worry.

Recently however, someone suggested that warming will allow some compounds that have been dropped out by CC to go back into solution so I've started to bottle at the same temps as CC (or a few degrees warmer, allowing for bringing out of the fridge, priming and letting sit for 30 mins or so).
 
My impression is that the co2 blanket has a finite life. How long does it last?

The reason I'm asking is because I cc all my beers and up until recently this question confused the hell out of me. Therefore I used to let everything warm to ambient before bottling so I didn't have to worry.

Recently however, someone suggested that warming will allow some compounds that have been dropped out by CC to go back into solution so I've started to bottle at the same temps as CC (or a few degrees warmer, allowing for bringing out of the fridge, priming and letting sit for 30 mins or so).

Judging by that infamous AHB article you are right with bottling cold:

So, if you are using a priming calculation that takes the residual CO2 into account, you are wasting time and energy, and possibly compromising your calculations, by warming your beer to ambient prior to priming and bottling. You may as well just get it straight out the fridge, and do it straight away. (You also have the benefit that you get less foaming when cold). The exception to this would be if you have had unstable temperature conditions during fermentation, and do not know what the temperature of your beer was at the end of fermentation.
 
i know your not trying to ague, just understand.
a couple of points i can address.
1. if the co2 layer has a finite life what causes it disappear? in a sealed vessel its happy to sit on top of the beer till disturbed by some process or external influence or removed. co2 is heavier than air so it will always displace air.
2.every time you rack it decreases the amount of dissolved c02 in solution due to stirring motion of the racking process no matter how gentle. so using a primary, secondary and finally a lagering vessel you have already decreased the dissolved co2. thus creating a new co2 layer in the vessel, providing it hasnt been purged with co2 before filling.
3.the bucket of water will absorb co2 but only up to the limits of the current atmospheric pressure. so therefore it will never reach even a light spritzing of carbonation at room pressure. it will have a higher level of dissolved co2 than one that is at the same temp but without the layer of co2.

but you can see why i say its the current temp rather than the highest reached.
say you have two beers. both reach say 22 in fermenting. at this point they have the same level of dissolved co2 you then rack both in to two separate but the same size secondry/ lagering vessel. the co2 is reduced at this point but still close.
you take one and put it at 2 degrees and the other at room temp.
you leave them for 3 weeks the one thats been in the fridge will have a higher dissolved co2 level than the one that hasnt.
this needs to be taken in to account as with some styles it could mean the difference between hitting the right carb and completely overshooting it.
 
Back
Top