Diy Drip Tray On Chest Freezer

Australia & New Zealand Homebrewing Forum

Help Support Australia & New Zealand Homebrewing Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Dicko72

Well-Known Member
Joined
16/9/10
Messages
63
Reaction score
1
Finally finished my Chest Freezer conversion... :D
Freezer.jpg

However I now need a drip tray!

Does anyone have any ideas for cheap DIY drip trays?

I dont really want to attach to the collar.
Would prefer liquid nails or magnets but would need to be pretty light I guess.
 
You could use the principle in mine - larger aluminium sheets are available - and hang off the tap shanks

Then use a hook system or L brackets for a drip tray (riveted or attached to the sheet)

http://www.aussiehomebrewer.com/forum/inde...st&p=776569

Magnets won't stick to a stainless drip tray - so they would need be glued - rare earth magnets will most likely be a must

Cheers
 
make the splash back of the drip tray to have holes at the spacing of your taps, the drip tray will hang off the taps and then can take the load of a full glass, as magnets and liquid nails probably wouldn't.

like this:
11F09124.jpg
 
Nice job on the Kegerator D!CKO, looks very smart indeed!

I've still got a cube cut in half on the floor because I can't think of something I'm happy with.

I must say it looks easy to clean up after a session with Cortez's setup, no scratching the Kegerator either...

Edit - as mentioned in other threads, good quality double sided tape is also an option.
 
Thanks all! Didn't think of hanging from the taps...
My intention is to expand to 6 taps when cash flow permits!

Like the idea of the splash back too. Awesome.
 
Nice job on the Kegerator D!CKO, looks very smart indeed!

I've still got a cube cut in half on the floor because I can't think of something I'm happy with.

I must say it looks easy to clean up after a session with Cortez's setup, no scratching the Kegerator either...

Edit - as mentioned in other threads, good quality double sided tape is also an option.

Thanks Logman. Still got some plumbing to do but almost done!

I was thinking of some guttering as an interim solution.
Currently I'm using foam and its not pretty!
 
I've got a rug 'down there' for now, does the job :eek:

I did find these guys who ship to Aus whilst looking around, could only find very expensive ones domestically
http://barsupplies.com/stainless-steel-drip-tray-p-349.html

You could stick it on the floor, or would Rare Earth Magnets hold it up (if you glued inside tray?)

Fabric is a much easier approach!
barsupplies link looks good...cheap is good!
 
You could stick it on the floor
They splash too much because of the high fall - if the tray goes on the floor the back splash area needs to be around six inches high. I hand a paint brush tray to start but the back wasn't high enough so I switched to the 1/2 cube.
 
Good point on the splash height, didn't consider that. I might stick with the rug until I can find a drownded kitten to slot underneath.
Fixing a drip tray seems like too much hassle (to me), kudos if you can summon the effort/come up with a workable solution.
PVC guttering sounds interesting, you could get pretty creative, some kind of water feature?
 
I looked at PVC guttering at Bunnings to put a piece on the floor but couldn't see any ends. Can you just buy a metre and block either end? If so, that would be good on the floor.
 
Does anyone have any ideas for cheap DIY drip trays?
If you watch ebay (search for 'drip trays') there are often very cheap (ex-UK-pub) plastic drip trays for sale, then it should be easy to make a L shape-type bracket that screws into the collar to hold them up.

Mine look like this (cost 1 plus plus a few $ postage):
driptray.jpg
 
All I have on mine is a couple of cheap L brackets siliconed to the front. Drip tray is a standard one that just sits on top, you can take it away and clean it easily.

Silicone on the bracket, hold it there for a few days with plumbers tape until the silicone cures and presto - no drilling or screws. If it can hold fish tanks together, it will hold a drip tray with a few glasses sitting on it.

Cheers :chug:
 
Silicone on the bracket, hold it there for a few days with plumbers tape until the silicone cures and presto - no drilling or screws. If it can hold fish tanks together, it will hold a drip tray with a few glasses sitting on it.
But once it is siliconed to the brackets how do you remove it for cleaning? :unsure:
 
I think the clue may lie above Wolfy ^_^
 
Finally finished my Chest Freezer conversion... :D
View attachment 47788

However I now need a drip tray!

Does anyone have any ideas for cheap DIY drip trays?

I dont really want to attach to the collar.
Would prefer liquid nails or magnets but would need to be pretty light I guess.
I've been using these ice cream containers for the last 12-18 months, they work great. A local ice cream shop will probably give you some if you ask nicely.
I don't know how some blokes pour their beers but mine all goes in the glass & the drip tray catches the couple of drips that drop after that.
Drip_Trays.JPG
 
I looked at PVC guttering at Bunnings to put a piece on the floor but couldn't see any ends. Can you just buy a metre and block either end? If so, that would be good on the floor.

I've seen some in bunnings comes in metre sections.
You can block off the ends with slot in divider things (designed for this purpose).

Reckon about $20 all up.

Pimp 'em up with a bit of spray bling....sorted!

Either that, or a line of Merkins as hsb suggests :lol:
 
But once it is siliconed to the brackets how do you remove it for cleaning? :unsure:


Silicone to the front of the freezer only. The tray just sits on top

If yoe ever need to remove them you can just cut them off with a razor blade.

:beer:
 
If you dont constrain yourself to pub style stainless steel, there are lots of options. Bamboo grows free along drains, floorboards can be found on verges. This drip tray is on a slope and has a drain to waste.

font.jpg
 

Latest posts

Back
Top