Search results

I have done some tests and the relay turns on as soon as I switch the power and it only goes off when I switch the power off. I have tested the diode and it is working fine.

some pictures of the board

Lorenzo, Brazil uses 220 and 110v. In Rio de Janeiro, where I live it is 110v

James, Thanks for the help, I will check the wiring today, specially the pump. I followed Mathos wiring diagram for that. On the heat element, I will do another test as It could have been done wrong. I ordered 110v element but they could have done 220v. Cheers, Luis

Max, yes I did read. The only part I did not configure any parameter in the settings, were the PID. Rgs, Luis

picture of the wiring, I'm following Matho's wiring diagram. From right to left; power in, Heat, Pump The blue wire from power in to heat is Neutral, all the other white wires are neutral All grounds connect to the SSR

Max, What configurations to I need to set? PID parameters? What is your suggestions for the values? I know Ardbir has no power output.

No parameter setting, I did the test in manual mode. Also, when I tested the power out for pump and heat in the controller; if I do Line and Ground, I get 66 volts and the same for Neutral and ground.

Hi James, I have some eletronics experience but it was 25 years ago, so I'm revisiting everything and going very slow to avoid risks. In my apartment, in Brazil, the power outlets do not have ground but I did all the installation with the ground. I have checked the fase and neutral from the...

Experts, My pot arrived and my mathos controller based on the 2.1 board is ready, the pump is not working and the element is heating the water extremelly slow. I tested the outlets of the controller, and they have 127v for the pump and for element. What may I have done wrong? Thank you...

Zwitter, Thanks for your answer and a 2nd SSR is a really good idea. I plan to have the controller away from the pot as another safety matter. Rgs, Luis

Hello everyone, I'm finishing up my Brauduino controller and have a doubt. I found 2 wiring diagrams in the forum; 1 from Matho and another one from lael for the latest kit and they have a difference in the pump wiring. On Matho's version, the load is connected to the pump and the neutral...

Lael, Just check the postage cost to Brazil and it is too high. It came to AU$92 with tracking number, otherwise it never makes it. So, I will have to give up on the kit. Thanks, Luis

+1 for silver

Lael, Looking great!!!!! Moving the buttons down seems the easiest solution. Cheers, Luis

So, on the pump, any recommendation? As I'm planning a 20L system, I taught the Braumeister pump would be smaller, quieter and could be installed without any support. Is the Chugger too loud and does it need to be properly fixed/level? Thanks,

Lael, Can the kit work on 110V? Also, I will buy the pump in the USA, so I can chose either one and their prices are similar. Rgs, Luis

Hello all, Just starting to plan my build and would like feedback in which pump to use? Chugger SS or the original Braumeister pump? Do I need to build a support for a chugger pump? Thanks, Luis

1. Lael (x2) 2. natdene 3. shaodw 4. gap 5. kingy 6. barneey 7. ArnieW 8. Putrino 9. Mitch_76 10. tateg 11. LiquidCurrency 12. rafinus 13. crazyhorse 14. marksy (x 2) 15. JB 16. Neo__04 17. Masters Brewery 18. Cervante 19. Cervantes 20. sipahono 21. BobCharlie 22. jubilakka 23. CoxR 24. Capnk...

Hey, I'm from Rio and live a couple of blocks away from Copacabana beach. :)