Search results

Australia & New Zealand Homebrewing Forum

Help Support Australia & New Zealand Homebrewing Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. H

    Herms control panel

    Check out electric brewery build on you tube and have a look through some of the overseas forums there are literally heaps of info out there just let your imagination run rampant. My brew rig is on Pge 44 under the old name of boybrewer
  2. H

    Herms control panel

    Electric or gas? Have a look at brew rigs on you tube . For gas check out Brutus 10 and there are heaps of electric ones as well
  3. H

    Herms control panel

    No worries. Do you have a brew set up if you do what is it BIAB DIY 3 vessel fill me in . I think if you have alook around page 47 you will see my set up in the show us your brew rig it has 2 kegs and a small 7lt pot as a herms with a single pump and the electronics box. I built the whole system .
  4. H

    Herms control panel

    Ok Do you have a brew system? If so what type of heating are you or want to use, what size is the system ?
  5. H

    Herms control panel

    There are quite a few posts on electrical systems for HERMS , if you use the search box you will find quite a few different ideas .Just type in herms and you will find a myriad posts on the subject .
  6. H

    Brew not bubbling

    The reason why your airlock is not bubbling,is your lid is not screwed down tight enough and the Co2 is leaking out through the seal .Don't worry too much about it just let it do its thing and then after a week to ten days check the gravity do this for two to three days in a row if the gravity...
  7. H

    FS Melb East. Grolsch bottles

    You tight arse you just want to make your $12 back on that new brew house .:p
  8. H

    FS: Pump, SS fittings, false bottom and other bits

    Thanks Poobah it was good to put a face to the name . I hope the first brew turns out well on the Brewmeister .
  9. H

    eBay stock pots

    So where is the warehouse !!!!!!!
  10. H

    Help needed: esky mash tun

    Go to Keg-king and look up BSP/NPT fittings page 2 and 6 you will find all the fittings you will need to fit out your mash tun and o ring to fit into the recessed nut .Failing that go to the big green shed plumbing isle half inch all thread and flanged nut , big arse washers with home made...
  11. H

    FS: Pump, SS fittings, false bottom and other bits

    Sorry Mardoo I have an IQ of 150 and I'm not crazy my mother had me tested :p
  12. H

    FS: Pump, SS fittings, false bottom and other bits

    I'll have the camlocks and the bulkhead fittings shoot me your number . I'm in Croydon can pick up
  13. H

    eBay stock pots

    Where is the warehouse ?
  14. H

    100 litre 3v electric brewery build

    Nice job on the stand love the 45* angle cuts . When I built my brew stand I just butt welded would have loved the 45* angle cuts it looks so much more professional . However having it butt welded meant that I could use the openings at the ends of the tubing which worked out well for I had a...
  15. H

    Herms for beginners

    Faaaark mate can I have one of those . Seriously nice job on the HEX .What you need to do now is stop asking questions and just brew, so by brewing you will learn to do it your way and make damn fine beer and probably a few mistakes along the way but that is just brewing .And what MJ said...
  16. H

    FS: 20L HLT with HERMS coil ($150, SYD)

    Mate do you want every nutter ringing you ? Delete your mob number if they want to contact you they will PM you
  17. H

    Mash out

    As Manticle said its not necessary. Check out Qld Kev he has a few videos and also one on cold sparging
Back
Top