Megaswill tap badges

Australia & New Zealand Homebrewing Forum

Help Support Australia & New Zealand Homebrewing Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Something like this? but with "property of cub" on the keg would be cool.
beer-keg-urinal.jpg
 
Something like this? but with "property of cub" on the keg would be cool.
beer-keg-urinal.jpg

I made one of these. Got it in the backyard at home. If I remember I’ll take a pic for you. It’s not mounted and plumbed yet, just sitting on an old 4wd tyre.
 
Hay all, I've a need for a bunch of megaswill tap badges, they're gunna go in the piss trough at the bar so folks can piss all over them, if you've got some laying about, I'll be happy to put them to good use

Cheers
I have a shit load mate. Reckon I may even have an old BEEZ NEEZ one. :barf:

Should I mail to the bar? How many do you want?

EDIT: Could be a ******* to clean?
 
I have a shit load mate. Reckon I may even have an old BEEZ NEEZ one. :barf:

Should I mail to the bar? How many do you want?

EDIT: Could be a ******* to clean?

gunna epoxy them all in so shouldnt be too bad for cleaning... need to find a g***e is***d one especially,

Ive got PL covered...
 
Lemme know if you still need more, I think I have several older ones tucked away.
 
P.M me your address and i can send a West End Draught and a VB tap handle. Maybe you could cut them in half length ways or cut the emblem out to suit your plans.
Either way post pics of the piss targets when done.
 
I made one of these. Got it in the backyard at home. If I remember I’ll take a pic for you. It’s not mounted and plumbed yet, just sitting on an old 4wd tyre.

Here it is. I actually needed to use it just now and remembered I needed to take a pic (before I used it...). It will one day be mounted up off the ground and plumbed to sewer and be flushing from a water tank. One day..
IMG_9508.jpg
IMG_9509.jpg
 
gunna epoxy them all in so shouldnt be too bad for cleaning... need to find a g***e is***d one especially, Ive got PL covered...





CUB_Badges.jpg


Before I send them, the badges I have are this type. Cast metal ones.I am just a bit worried about how you will fix them securely to your urinal? They have a bit of weight in them, and do not have flat backs on them.
 
Last edited:
View attachment 110349

Before I send them, the badges I have are this type. Cast metal ones.I am just a bit worried about how you will fix them securely to your urinal? They have a bit of weight in them, and do not have flat backs on them.
While I like the concept of this idea I'm not completely sold on the practicality. Men's urinals are generally not known for their overall cleanliness when you've got a smooth stainless trough. I'm thinking these would help generate some extra "splash back"??
 
While I like the concept of this idea I'm not completely sold on the practicality. Men's urinals are generally not known for their overall cleanliness when you've got a smooth stainless trough. I'm thinking these would help generate some extra "splash back"??
Agreed. They would provide quite a handy bacteria trap for nasties to thrive in as well.. It my be that @Yob wants the Old School flat vinyl ones?
 
The devil in the detail is that moisture creeping up the bondline is the common method of failure for epoxy bonds. It is very difficult to achieve an epoxy bond to metal that will survive hot washing.

To get this to work you are going to need a specialist epoxy and good surface prep. I would use Kinetix R246TX with their H126 ultrafast hardener, that will give you an epoxy which will withstand 120 oC once it is post cure baked (most ordinary epoxy won't survive much past 80).

Pretreatment of the stainless surface with sulphuric acid / oxalic acid etch followed by a chromic acid de-smut will improve bond strength hugely.

Be very careful with the chromic acid: it is corrosive, toxic, carcinogenic, mutagenic and a severe pollutant.
 
Back
Top