Hops and PH

Australia & New Zealand Homebrewing Forum

Help Support Australia & New Zealand Homebrewing Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Osangar

Well-Known Member
Joined
17/9/06
Messages
130
Reaction score
25
Location
Singapore
Hello brewers,

in an effort to improve my brewing, I'm monitoring PH. my home water has high ph and I adjust using lactic acid.

I have been adding grains to the mash water (only mineral adjustments made) and let it sit at 30c for 30min. then check PH. adjustments are made at this point

I've noticed however after hops are added to the boil, the ph appears to go up. is this common. do hops add to the akalinity of the water ?
 
Literature says yes, but only a smidge, have seen numbers like 0.003pH/g/L. So we aren’t talking vast swings in pH even in very heavily hopped beers. That’s mostly in dry hopped beers, could be a little different for kettle hops.

You would want a better than average pH meter to be trusting the results too far, it could be an artefact of the changing conductivity introduced by minerals in the hops, no one has come up with an explanation yet.
Worth having a look at the final pH and if it’s outside the optimum range adjust with Lactic acid at need. Post fermentation pH adjustments can make a big difference to how a beer tastes.
Mark
 
thanks mate.
my experiments so far have shown taste improvements from adjusting the post mast, pre fermentation ph. it is something that was surprising the variation across a few styles I've tested so far.
 
Maybe just to go back to basics for a moment
It's prety much a truism that pH should fall at every step in the process and mostly by the same mechanism. Namingly the reaction between Calcium and Phosphates in the malt forming insoluble Calcium Phosphate. The obvious limitations being the availably of Ca and Phosphates. Given enough Ca as part of your salt additions to mash and sparge water (50-100ppm at a minimum). The limit becomes Phosphate availability, not all the Phosphate is available initially, some of it is bound up in organic complexes that are liberated during the mash and boil, so we should see a steady fall in pH as Phosphate becomes available.
For this reason in a pale beer mash (bit different for dark beers as Melanodins are acidic), no matter how much Ca we add as salts the initial mash pH in distilled water will rarely get under 5.6pH, somewhat above the ideal for mash enzymes. Adding acid to reach the optimum pH is again pretty common practice.
Using acid to adjust end of boil pH to the optimum for the yeast and adding some of your Calcium at the end of the boil are both pretty common to (well in really big breweries).

So yes I'm pretty much going to agree with you having the pH on target at every step will improve your beer.
Baring the unexpected, if your mash pH is on the money and your water chemistry is good (lots of Ca say >150ppm) and you dont have too much residual Carbonate, your pH should stay on track, you should also have plenty left over for the ferment where it benifits yeast and helps with flocking and sedimentation of both yeast and some of the other break material.
If you want kettle finings (Carrageenan) to work well, the pH is critical there to, being not far from target can have very negative effects on how well kettle finings work...
It's also well worth testing end of ferment pH to. Small adjustments can make a big difference there. Beer over the range of 4.0-4.5pH can go from being described as Too Sharp - Brilliant - Flabby (the average for Lager/Pilsner styles is around 4.1-4.2pH). Well worth doing some tests in a glass you just need some Lactic acid, a bit of Bicarbonate (make a solution) and a good pH meter.

Look forward to seeing how you go, please keep us informed, this is an important and often much ignored part of brewing.
Mark
 
this is the matter that has me most baffled, and I suspect is in a mineral deficiency in the water I'm using. yes, the ph should decrease at each step. however, I'm finding it increases post mash. most confusing.
ill keep updating on the progress. my current beer has just gone into the fermentor, so in two weeks, ill test again
 
Back
Top