Diy Computer-fan Stir-plate Build

Australia & New Zealand Homebrewing Forum

Help Support Australia & New Zealand Homebrewing Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Wolfy

Well-Known Member
Joined
18/12/08
Messages
3,872
Reaction score
64
Location
Melbourne
The epic 36page 6-year-old 'Tight Arse Stir Plate' thread has some great ideas, but with so much information it might appear that making your own stir-plate look more difficult than it is.
These are the DIY Computer-fan Stir-plate assembly instructions that work well for me, and (I hope) are easy for everyone to follow.

The first stir-plate I built this way has been in use for the last 2 years, and is still going fine, the two updated versions work without problem with starters ranging from 50ml to 4L.

Total cost is about the same as that of a pack of liquid-yeast.

Equipment (see next post for alternate suggestions):
stirplatebuild1.jpg

120mm speed-controlled Computer fan, "Scythe 120mm Blue LED with VR Fan (SY1225SL12VBL)".
12V DC power adapter, (cheap) from Ebay.
8x 8mmx1mm rare-earth magnets, same as the cheapest ones on Ebay when searching for 'rare earth magnets'.
A standard (cylindrical) teflon-coated stir-bar (from lab-supply shop), 20mm and 26mm long ones work well for this set-up.
An enclosure, screws etc to mount the fan/stir-plate.
Superglue to stick the magnets to the fan-hub.

Optional:
On/off switch.
Solder, a few bits of wire, gaffer-tape, electrical tape, heat-shrink-stuff.

The good thing about the 'speed controlled' Computer fan is that it comes with its own adjustable speed-control knob, so you don't have to worry about adding that yourself:
stirplatebuild2.jpg


The tricky part of the stir-plate assembly seems to be getting the magnets positioned correctly.
I use 8 of the 8mm x 1mm round rare-earth magnets, with 2 stacks of 2 on each side of the fan-hub, as per the picture below.
This size and arrangement works well with the fan-hub, and stirs well on all flat-bottomed starter-containers that I have tried.
stirplatebuild3.jpg


Attach the magnets with super-glue, but some care and attention is needed, since they will 'interact' with the copper coils inside the fan and once you have placed one, all the others want to try to stick onto them. Draw a line across the middle of the fan-hub and then arrange the magnets along that line. Try to space them evenly since that will help keep the fan balanced (try to do a better job than I did here, also try not to stick your fingers together or to the magnets or fan with the superglue).

If you buy your stir-bar before you place the magnets, I have found that the best spacing for the magnets is to have them as wide apart as the stir-bar is long (as per the picture below), closer or further apart does not work as well, but the distance is dependent on the length of your stir-bar.
By using 2 sets of magnets, both a smaller and larger stir-bar can be used.
stirplatebuild4.jpg


To assemble the stir-plate, cut the plugs from the power-adapter and the fan, and then strip the wires.
Connect the appropriate wires (positive/negative, usually red/black) from the power supply to the fan (red and black wires, the yellow wire is not used, so simply cut it off and ignore it).
The connection will be 12V and the fan will only work when they are connected correctly, so you can easily join the wires together to ensure that it works before you attach them permanently.
Solder and shrink wrap are the best way to go, but the wires can simply be wound together by hand and then wrapped with electrical tape.
stirplatebuild5.jpg


An on/off switch allows the stir-plate to be controlled without having to pull the plug from the wall, simply wire the power-supply wire(s) to one of the switch's terminal(s), and the fan-wire(s) to the other.

Now all you need to do is to mount the fan/stir-plate in an enclosure (see below for more info).
 
There are many variations of equipment that all work much the same way, you might already have most of the items, and so any additional costs will be minimal, read through the Tight Arse Stir Plate thread if you want more info.

Any size computer-fan will work, however I find the 120mm fans are easy to work with and the fan-hub is a good size for the size stir-bars that I use.
Most any old computer, or computer power supply will have a fan you can use, simply remove it, strip the wires and use it as outlined above.

(Old) Computer disk-drives have strong magnets inside them that can be removed and glued to the fan-hub, this works fine, but is more effort and since the magnets are a U-type shape with both poles on the same magnet, they are harder to adjust and tend to be a little more uneven. The rare earth magnets are very cheap on Ebay, so I find them a much better solution.

Any 12V DC power supply should work fine, if you have an old (unused) one from a mobile phone, cordless drill or other electrical device, there would not be any need to buy a new one. Computer fans also function from about 5V up to about 15V, so in theory any DC adapter in that range will work, however it will change the speed the fan works at, and may make it too fast or too slow. Old computer power-supplies can also be used, however they tend to be large and cumbersome, but if you have one it is possible to short the on/off leads and use the 12V supply from that to power the stir-plate. It is also possible to use power-adapters used for external computer-hard drives or the like, since they will usually supply 12V, it is just a matter of identifying which wires are which.

If you do not have a 'speed controlled' fan, you can adjust the speed of the fan by altering the voltage, this can be done with a variable power supply or by changing power supply, however I have found that the continuous-dial-type-speed adjustment works much better than the 'steps' that variable power-supplys offer, and that it is much easier to get the stir-plate working correctly if you can fine-tune the fan-speed. A potentiometer is also a good way to control the fan-speed, it just requires a little bit of extra electronics.
A search on Ebay for "LED Dimmer" should result in a number of (different types) of LED Dimmers, used for LED lights, these would also make a very good pre-made speed controller for a DIY stir-plate. Simply wire them in between the power supply and the fan, and they would provide continuous speed-adjustment.

While the teflon stir-bar will not be cheap (for something so small) they are designed for the job and work very well, some people have used various magnetic or metalic items, but especially if you have lab-glassware the additional expense of a real stir-bar is well worth it. They can also be boiled/sterilized when you make your starters simply by dropping them into the starter-flask while it is on the stove. The standard cylinder type stir bars work best and are much more quiet than the strange shaped ones or ones with a pivot in the middle, and if you are going to use the stir-plate in your house, keeping it quiet is good. :)
 
Enclosure.

A quick browse through the pictures in the Tight Arse Stir Plate thread will show that there are many ways to mount the fan/stir-plate.

When mounting the fan, obviously the magnets need to be on the 'top' as close to the top of the enclosure as possible without actually rubbing against it when it spins (make sure you check before turning the fan on).
Solid, thin, non magnetic or metallic materials (usually plastic) work best, but the type of enclosure you use often depends on what materials or skills are at hand.
Nice wooden, plastic or perspex enclosures can be made if you are skilled working with those materials.
Pre-made hobby/jiffy boxes are common, but anything else can also be used, a children's plastic lunch-box, a plastic kitchen-container, a CD spindle, a bucket etc, the list is almost endless.

Try to ensure that the the top of the enclosure is fully covered, yeast-starters can over-flow the container, and drip down and short-out the fan, which is something best avoided (the first stir-plate I made caused some nice fire-works in the lounge room this way).

In this case I used the lid from an old Coopers-type fermentor, since I use cling-wrap when fermenting beer, the lids are essentially rubbish now.
It looks ugly and I hope that others make stir-plate enclosures that look nicer, however it is solid, the fan fits perfectly inside the 'indent', the size makes it impossible to tip over, and it easily holds even a 5L starter.

From below, On/off switch and speed-control at the top, power supply at the bottom of the photo.
stirplatebuild6.jpg


And from the top it looks something like this, gaffer tape is ugly but practical and saves scratches on the glassware from the screws, gluing the fan was an option but its nice to have it removable if it needs to be adjusted :
stirplatebuild7.jpg


In-action shots (stepping up a lager yeast):
stirplateV4.jpg


I grow my starters in the lounge-room since that is the most comfortable temperature all year round (Air-cond in summer and heated in winter), but since I live in a normal (maybe a tad messy) house, with a cat, open doors, dust and all that I try to keep the starters covered at all times (when not taking photos):
stirplatebuild9.jpg

stirplatebuild10.jpg
 
So Wolfy, is that stir bar pictured about 2 cm? What size stir bar is best all rounder for starting off?

Great threads and nice tea towels
 
Very nice work Wolfy. Simple cheap and nicely explained with photos.

Maybe you should copy this into a PDF file and submit into the articles section.

Cheers SJ
 
So Wolfy, is that stir bar pictured about 2 cm? What size stir bar is best all rounder for starting off?
It's in use now, so I can't really measure it, but a stir-bar between 2 and 3cm should work fine, I wouldn't go any smaller or larger than that.
Maybe the wee lil yeasties can learn Welsh while they grow up!
LOL, the in-laws visited the UK last year, and didn't bring me home any beer-stuff so the tea-towels have to do. :(
 
I can't edit my first post now, but I forgot to add this information about aligning the polarity of the magnets when gluing them to the fan-hub:

The ends of the stir-bar will have opposite magnetic polarity, so each set of 4 magnets (on opposite sides of the fan-hub) must be arranged so that their magnetic polarity is the opposite to the ones on the other side. Essentially one set of magnets 'push up' and on the other side of the fan-hub the magnets 'pull down', this way the corresponding 'opposite' magnetic attraction from the ends of the stir-bar will 'lock on' to the magnets as the fan spins (even at 1600RPM the stir-bar shown in the picture below will stay firmly attached to the magnets).
(If you placed all the magnets the same way up, one side would repel rather than attract one end of the stir-bar.)
 
While the teflon stir-bar will not be cheap (for something so small) they are designed for the job and work very well, some people have used various magnetic or metalic items, but especially if you have lab-glassware the additional expense of a real stir-bar is well worth it. They can also be boiled/sterilized when you make your starters simply by dropping them into the starter-flask while it is on the stove. The standard cylinder type stir bars work best and are much more quiet than the strange shaped ones or ones with a pivot in the middle, and if you are going to use the stir-plate in your house, keeping it quiet is good. :)

I was going to post something about the stir bar losing its magnetism when heated, but a quick check on Wikipedia has confirmed no-one should ever even get close to it (look up Curie temperature). Sometimes I like to sterilise with a plasma torch though... :rolleyes:

But seriously, excellent post.
 
A few days later and a good dose of patience to get it working on the decidedly round-bottom 5L glass demijohn:
stirplatebuild11.jpg

(ps: Donations of 3, 4 an 5L Erlenmeyer flasks are most welcome).
 
have you got a good online source for the fan and stir bars. I have found the fan on ebay for around $35 delivered and I have fired off an email to Science Supply in Mitcham for the stir bars. Any other options? No spare time during business hours unfortunatly so online stores who post would be handy.
 
have you got a good online source for the fan and stir bars. I have found the fan on ebay for around $35 delivered and I have fired off an email to Science Supply in Mitcham for the stir bars. Any other options? No spare time during business hours unfortunatly so online stores who post would be handy.
SSC is where I got my stir-bars from, however I picked them up rather than having them delivered, there are a few other similar online shops (often the same as supply flasks and test tubes) but I don't have a list of them I'm sorry.

I paid $12ea for the fans, on special at PC Case Gear, if you can't find a cheaper source for the fans (google for the model number) I'd be tempted to use a generic fan and dimmer switch due to the difference in price.
 
Jarthy, just be aware that many people who have a stir-bar with a pivot ring (the wiltronics ones) have said how noisy they can be.
 
I just ordered the magnets, LED dimmer, and stirbar from ebay, ended up getting an egg shaped stir bar instead of a pivot ring. I have plenty of 80mm fans and hopefully I can dig up a 12v phone charger from somewhere.

Thanks for the suggestions.
 
Inspired by the diy stir plate, have received some ebay purchases and have wired a power supply ($3), led dimmer ($7) and fan (old PC) together. It works really well. Just need the magnets, stir bar and flasks to arrive. Haven't considered the housing yet. I want to internalize the dimmer and it's pretty big.

Didn't bother with the switch (5 for $2 delivered - ebay), the dimmer turns off.

DSC_0242.jpg

The connection of the fan to led dimmer is screwed in, will make it easy to swap fans, power supply etc.
 
I bought the same dimmer, pretty nifty. I just mounted the dimmer's box internally, but attached the dial into the wall of my stir plate housing. It comes apart easily and has a nice long cord to the pot.

no pics atm :X
 
I am trying to get my head around a few things. I am not a sparky or electronically minded. Please tell me how I am going so far:
I know with my stirplate when I have a large volume on top of it (say 2.0L+) at higher gravity (OG say 1.040) it most times doesn't show a whirlpool/vortex, particularly not during krausen but shows after that when it has fermented and the gravity is lower and the yeast is settling out. Perhaps it has to do with the viscosity of the starter (as expressed through specific gravity reading)- fermented is thinner?
So I am thinking grunt is good.

Since I want to build a TASP, this got me to thinking and Googling and thinking some more.
There has been talk of dimmer switches etc and voltage regulation for speed control. These lower the voltage to lower the speed of the fan but less voltage equals less torque. Lower speed = lower grunt.

PWM (Pulse Width Modulation) seems to me to be the shizzle. You can control the speed of the fan but still retain pretty much 100% of potential torque because they are still at 12 volts. Lower speed = same grunt. (also less heat generated). It seems a lot of computer fans have four pin plugs because there is a PWM function on the computer motherboard = not useful to me.
There are some schematics for PWM units you can solder up on circuit boards yourself = not my bag baby.
There are commercially available PWM units for high voltage motors = not useful.
I found a few 12 volt PWM 'kits' but these are for 20 -30 amps (lowest I found was 3A) not 0.3A or so of a computer fan = not useful to me.

Does anyone have a solution for an external PWM for a computer fan?
Have I got it all wrong?
Am I chasing something that doesn't need to be chased?
 

Latest posts

Back
Top