CraftBeerPI Brew Controller

Australia & New Zealand Homebrewing Forum

Help Support Australia & New Zealand Homebrewing Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I have v3 installed I have set a static ip on my pi but cannot get the web interface to connect. I see the craftbeerpi splash screen on my pi's boot screen. Is there something I need to enable or configure to get the web interface working?
 
It should be accessible in chrome at 10.0.0.xx:5000 (replace the xx with your RPi’s IP address )

Make sure you have v3.0
 
I went through the same thing last year checking out v3.1_alpha, it set up a second IP address changing the address I had bookmarked.
 
[QUOTE = "Manuel, post: 1368635, member: 44687"] Hola,

Me gusta presentar mi controlador de infusión base Raspberry PI CraftBeerPI.

caracteristicas:

- Controla tantas teteras como quieras
- Control de hardware: agitador, calentador, bombas, válvulas
- Asistente de instalación
- Pasos de preparación flexibles
- Pasos automáticos y manuales
- Interfaz de usuario de teléfono inteligente, tableta y escritorio
- 3 logotipos automáticos de caldera estándar
- La lógica personalizada se puede implementar fácilmente
- Libro de recetas
- Tabla de temperaturas para cada caldera
- Soporte para conexión directa GPIO, PiFace o Gembird USB
- Soporte para Fahrenheit y Celsius
- ¡Gratis!

Sitio web: www.craftbeerpi.com
Facebook: facebook.com/craftbeerpi

Aclamaciones,
Manuel

Img1.png


Img2.png
Img4.png
Img8.png
[/CITAR]

Hi,

I like to present my Raspberry PI base brew controller CraftBeerPI.

Features:

- Control as many kettles as you like
- Hardware control: agitator, heater, pumps, valves
- Installation wizard
- Flexible brew steps
- Automatic and manual steps
- Smartphone, tablet and desktop user interface
- 3 standard kettle automatic logics
- Custom logics can be implemented easily
- Recipe book
- Temperatur chart for each kettle
- Support for direct GPIO, PiFace or Gembird USB Socket
- Support for Fahrenheit and Celsius
- Free!

Website: www.craftbeerpi.com
Facebook: facebook.com/craftbeerpi

Cheers,
Manuel

Img1.png


Img2.png
Img4.png
Img8.png
hello how are you, I am from santa cruz bolivia, I want to build a craftberr in a raspberry, the equipment will be 3 containers and I would like to control the agitator, 3 water pumps and solenoid valves for a gas system, you could help me to make it from the PCB board, until the programming. my email is [email protected], whatsapp +591 70842029
Thank you
 
Hop addition times...

Did my first brew over the weekend, i dont know if my hop additions were bugged, but i put them in how i normally did in my STC-1000 (60, 15,10, 5, 0)

The hop alerts did't pop up at the expected times. Is this the right way to add them?
 
Screenshot_1.jpg

so 0 addition alert was as soon as the timer started. (10 min timer)
Hop 3 alert went off at 8mins...
 
so 0 addition alert was as soon as the timer started. (10 min timer)
Hop 3 alert went off at 8mins...

As you have found it is backwards to how you would normally refer to hop additions. The hop timings are minutes from start of boil.
 
As you have found it is backwards to how you would normally refer to hop additions. The hop timings are minutes from start of boil.
*sigh* well thats just silly...
 
The good news is that you can actually code your own boil logic if you'd like to change it :)
 
I hope this is the right place to ask this:

Does anyone have a full wiring diagram for an Australian brew panel using a CraftbeerPi? If not is there a PID style panel wiring diagram that is best to modify?

A list of parts would also be very helpful.

Thanks
 
The good news is that you can actually code your own boil logic if you'd like to change it :)
I think the boil logic is seperate from the boil step control, even after changing boil logic, the step control is the same
 
Sorry to disturb you

I am looking to buy a v2 card but I can not find and on the official Facebook page I have no answer! Do you have a link ?

Thank you Good day
 
Back
Top