Search results

Australia & New Zealand Homebrewing Forum

Help Support Australia & New Zealand Homebrewing Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. stew.w

    Shed Cleanout

    plate chiller is gone. anyone want any of the other stuff? pm me
  2. stew.w

    Shed Cleanout

    Yeah its this one. http://kegking.com.au/heating-cooling-equipment/keg-king-chillout-mkiii-30-plate-heat-exchanger.html Been sitting in my shed for a few years. Just never got around to using it
  3. stew.w

    Shed Cleanout

    You'd have fight my daughter for them
  4. stew.w

    Shed Cleanout

    4 tap flooded font - $250 2 tap font - $100 2 x 2 tap font (both incomplete) - $100 one is just missing 2 ring nuts the other a bit more keg king plate chiller - $80 (never used) in ACT cheers, Stewart
  5. stew.w

    Glycol Chiller

    i have a glycol chiller that i was intending on turning into a portable bar but i dont think i'll ever get around to it. has a stainless steel tank, stainless steel evap coil and 2 stainless coils for the beer lines. controlled via and elliwell controller and runs on r404 (gas which has no...
  6. stew.w

    Calling fridgies - Building a coolroom (advice needed)

    yeah ac compressors arent meant to run those pressures, depending on how old it is it may just go into fault if the coil temp got that low. pulling apart a fridge wouldnt work either because the capacity wouldnt even get close, if you get a packaged unit get a r134 unit because it is the...
  7. stew.w

    Calling fridgies - Building a coolroom (advice needed)

    https://www.google.com.au/url?sa=t&source=web&rct=j&ei=h5CZU-CAHcXmkgWkkYDIBg&url=http://www.heatcraft.com.au/component/docman/doc_view/65-kirby-drop-in-packaged-refrigeration-units&cd=2&ved=0CDEQFjAB&usg=AFQjCNFNbSjxQxTVe71AG2Ryq1pa0mt5gA&sig2=DPehiZCkoZO8FBPwKZurbw
  8. stew.w

    Calling fridgies - Building a coolroom (advice needed)

    U can buy packaged cool room units. I'm a fridge too and have put some in. Unless you seal the room u are going to have endless problems with iced up coils if you are talking about running this at fridge temps. I think if u bypass an ac unit thermostat to run those temps the compressors just...
  9. stew.w

    Show us your brewrig

    Started this thread a few years ago. Still using essentially the same setup as before but I have added a rims tube, pump and electric hlt with temperature control. Just gotta add the plate chiller that ive had for about a year, no chill is just too convenient. Got the hlt from a bakery, it was a...
  10. stew.w

    Wtb: Auberins 40a Ssr

    you can tell its switched on mine by the light on it, but you could also meter the amps with an amp clamp. Cheers, Stewart
  11. stew.w

    Wtb: Auberins 40a Ssr

    also just because the output of your ssr has 230 volts doesnt necessarily mean it has switched, mine has 230v the whole time but doesnt let any current through until switched.
  12. stew.w

    Dedicated Herms Guide, Problems And Solution Thread

    i did the first time i used mine but that was because i didnt throttle the pump back, i have the ball valve on the pump outlet about half closed. maybe your crush is too fine, apart from that im not sure what it'd be. Cheers, Stewart
  13. stew.w

    Monster Mill - 2 Roller Stainless

    i had something similar with mine and it was because the rollers weren't alingned. one sides gap was slightly bigger than the other, once i re-adjusted it worked fine. Cheers, Stewart
  14. stew.w

    Fitting Taps To A Fridge - Advice Needed

    theres still often lines in the walls as they can be used as door heaters so the door wont freeze shut. so i would say that there probably is lines in the walls. be carfull drilling it, why are you going through the side and not the front anyway?
  15. stew.w

    Dedicated Herms Guide, Problems And Solution Thread

    pretty sure it was a flour bin from a bakery. makes a good HLT and is pretty thick SS too
  16. stew.w

    Dedicated Herms Guide, Problems And Solution Thread

    finally got my RIMS set up going this week and did my first batch on it today. brew went great, probably need to tune my PID a bit better as it overshot a couple of times, but apart from that everything else works. did have one problem with an air lock in the silicone tube where it loops up to...
  17. stew.w

    Video Games

    halo anniversary should be cool, especially if you played halo 1 as much as i did. skyrims the one im looking foreward to though, oblivion was awesome.
  18. stew.w

    Dedicated Herms Guide, Problems And Solution Thread

    just use teflon, i wouldnt use a thread sealant as it might leach into your brew.
  19. stew.w

    Hot Water Service As A Hlt

    http://www.rinnai.com.au/images/stories/br...rence_Guide.pdf have a look at page 2, you can get a 85 deg rise in temp @ 9.9 litres a minute, but i dont think they're cheap. personally i wouldnt buy somthing that doesnt have an AGA approval as an electronic device controlling gas flows and...
  20. stew.w

    Hot Water Service As A Hlt

    you can install a rinnai inside a house it just needs to be an internal unit flued outside which is easily done, have a look at commercial hot water units or instantaneous commercial ones. commercial kitchen hot water supply is about 82C. from what ive heard you can get a rinnai domestic unit...
Back
Top