Search results

Australia & New Zealand Homebrewing Forum

Help Support Australia & New Zealand Homebrewing Forum:

  1. F

    Perth Cornelius Keg Buy

    Hi guys, Been out of it for a while but getting back into brewing, need a few more genuine cornelius ball lock kegs and came across this ad on Gumtree: http://www.gumtree.com.au/s-ad/ballajura/miscellaneous-goods/keg-beer-post-mix-cornelius-ball-lock-19-lt-for-home-brewers/1063895708 Rang the...
  2. F

    Mashmaster Fridgemate Probe

    Hi guys, I am looking at ordering one of these and have alreadly asked BrizzyBrew the question but it seems he is away so could anyone with one of these units answer me this:? Is the probe stainless and suitable for immersion? What I intend to do is put a compression fitting on the probe and...
  3. F

    Soft Drink Kegging Questions...

    Few quick questions....I have my converted freezer setup and all is running smooth at about 3degC. - My compressor on the freezer fires up and cools it to about 1.5 degC and then it slowlys warms back up to 4.5 degC (probably takes half an hour) before it kicks in again....Is this normal or is...
  4. F

    Freezer Controller Feat. In Silicon Chip Magazine

    Hey guys, I noticed that this thermostat was discussed some time ago by a few members, basically I need one now (asap) and was wondering if anyone has come across where you can indeed purchase these? Are they stocked at Jaycar & Are they indeed a good unit? Full Article...
  5. F

    Pump Flow Rate

    Who here is good with plumbing math? What i am trying to do is calculate how much pump pressure or head height i will need to pump the following (for my still): The water will travel from a holding tank through around 5 metres of either 6mm or 12mm hose (garden hose) to the still which has a...
  6. F

    Mini Fridge

    I have a bit of a situation on hand, since my old man cracked it that I had my keg in the drinks fridge (read big) i've since had to take it out which doesnt leave me with any quick fixes in the meantime till I get some freezer conversion or something happening. However I have this Red Bull...
  7. F

    Kegging Newbie Help

    ok guys, Now that I have all my gear and will hopefully be getting my extinguisher back tonight, i've done a little research and tried to devise a method of how to go about kegging bourbon + coke - since i presume its a little different to beer. Here is what I have come up with - need help...
  8. F

    New Smc7008abr Dsl 8-port Router W/ Print Server

    The unit is a 8 port Cable/DSL router with a COM port for dialup when the primary connection goes down - or you can use the unit just for dialup (god forbid). Also has a inbuilt power supply (no plug pack), is rack mountable with brackets supplied and has a built in print server. Full...
  9. F

    Round Eskies

    Hey guys, i've been looking around trying to find some round insulated eskies large enough to submerge a whole 5gal keg in ice. So far I have come up with lots of ones that fit the 3 gal and the following: http://www.morleyathletic.com/images/M14976.jpg (Fits a whole 50L keg even)...
  10. F

    Keg Diptube Question

    Quick question guys, If I lay the kegs down horiztontal in an esky and hook up the gas (vertical) will they still be able to be dispensed properly or will the tube not pick up all the liquid correctly?
  11. F

    Extinguisher Head

    Guys, A few quick questions about my new extinguisher I have picked up (see attached image) : - Is this the right thread for a CO2 regulator to fit straight on or will I need to swap it out for another? - When I removed the diptube the brass fitting comes with it (ie. there attached), Should...
  12. F

    Picnic Dispensing

    hi guys, just some more questions about dispensing at a party/picnic.... 1. Esky big enough to fit a keg, submerge the whole keg in ice. Gas outside. 2. Keg and gas outside esky, pass liquid through cooling coil submerged in ice within the esky. Which is the better option and why? Cheerio...
  13. F

    Mlf/barb Quick Disconnects

    Hi guys...Im ordering some gear from BrewersDiscount and was just wondering whats the norm or whats better in relation to Quick Disconnects: - Plastic / Stainless.....Stainless not worth it? 3 times the price.... - MFL / Barb......Is MFL where you buy a femal MFL to barb 1/4" fitting which is...
Top