Recent content by Moray

Australia & New Zealand Homebrewing Forum

Help Support Australia & New Zealand Homebrewing Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. Moray

    Help With Networking Win7 To Xp

    On the win 7 box run gpedit.msc as an admin. under local computer policy expand computer configuration, windows settings, security settings, local policies, security options. Find accounts: limit local account use of blank passwords to console login only and change the setting to disabled.
  2. Moray

    Arduino Development Thread

    Saw this on the brewtroller forum, berfridge http://www.elcojacobs.com/uberfridge/
  3. Moray

    Arduino Development Thread

    What size ssr do I need to control a 15amp element, is 25 amp ok or do I need a 40 amp?
  4. Moray

    Arduino Development Thread

    Would one of these LCD shields with keypad be ok for display and input ? http://www.ebay.com.au/itm/LCD-Keypad-Shie...6#ht_1979wt_689
  5. Moray

    Arc Welding Stainless

    Well I've now succesfully done it. I used 2.5 mm rods and did it in six tacks per socket. I gave it a few minutes between each weld, and did each weld on opposite sides. I also screwed in a length of threaded pipe whilst still hot to ensure it still fitted. It was pretty easy, and didn't blow...
  6. Moray

    Arduino Development Thread

    Yet another senior sys admin/ infrastructure dev here. To get this thread back on topic, how do you set temps Hard code them, or can you setup some kind of input device?
  7. Moray

    To Dig Or Not To Dig

    Should rhizomes be dug up and split every few years? Or do they just keep getting better with age
  8. Moray

    Arc Welding Stainless

    Thanks everyone for your advice. I've got a spare socket and have the cut off top from the keg to practice on. I was thinking of getting these rods, as they say they are suitable for 304 (keg) and 316(socket) http://www.bobthewelder.com.au/product.php...=151&page=1 I think I'll try the...
  9. Moray

    Arc Welding Stainless

    I would like to weld a couple of sockets to a keg to convert it into a mash tun. If I use 316 stainless electrodes can I do this with an arc welder? Are there any tips or tricks that might help me do this.
  10. Moray

    Paragliding

    I mostly fly coastal sites. The main sites down here are flinders, cairns bay, portsea back beach. On the west coast there's bells beach, red rock, fairhaven, Apollo bay. Check out the site guide on the vhpa site. http://www.vhpa.org.au/ Nothing better on a nice sunny afternoon, flying above...
  11. Moray

    Homemade Keg And Fermenter Washer

    The holes in the endcaps are slightly smaller than the outside diameter of the hose. I cut the hose ens at an angle and heated it in hot water until it became maliable it was then quickly pushed into the hole. I used a pair of needle nose pliers to grab the end from the inside and pulled it the...
  12. Moray

    Homemade Keg And Fermenter Washer

    Hi all, being a lazy brewer I decided to make keg washer, as I was finding pulling them apart for a good clean too much work :P I went shopping and got the following parts; 1 meter 15mm pvc pipe 2 x 15mm PVC T's 3 x 15mm PVC end caps 1 x 15mm PVC joiner 1 x 15mm to 1/2 inch...
  13. Moray

    Free Glass Longnecks - Melbourne

    Adam, I've sent you a pm cheers Moray
  14. Moray

    Free Glass Longnecks - Melbourne

    Hi all, I'm just cleaning up my garage and have about 4 dozen glass longknecks I'd like to get rid of. So if there are any brewers who are after some glass bottles please let me know. cheers Moray
  15. Moray

    Fire Extinguisher Co2 Bottle

    Hi Matt, I got mine from UFE in Moorabin about 2 years ago. http://www.ufeservices.com.au/ it ran out over christmas, so I got it refilled there last month. It was cheaper than a LPG swap and go refill
Back
Top